Window Replacement Cost in Raleigh, NC (2026 Price Guide)
The short answer
You live in a two-story from the nineties, somewhere off Falls of Neuse or out toward Wakefield. A handful of windows have gone milky between the panes, two won't stay up without a paint stick, and the wood trim outside is soft enough to push a thumb into. That's the usual Raleigh window job. Here's what it costs.
Replacing all the windows in a typical Raleigh two-story (about 18 openings) with white vinyl insert windows runs roughly $10,000 to $18,000. That's $550 to $1,000 per opening, installed.
The other common versions:
- Vinyl, full-frame (new exterior trim and flashing, old frames torn out): about $900 to $1,600 per opening, or $16,000 to $29,000 for 18.
- Fiberglass, composite or wood, usually from the national brands that send a salesperson to your kitchen table: about $1,100 to $2,200 per opening, or $20,000 to $40,000 and sometimes more.
- Big picture windows and odd shapes: $1,500 and up each.
- Just the fogged glass, in a frame that's otherwise fine: about $200 to $480 per pane.
Add 7.25% sales tax to any of those if the quote doesn't already include it. More on that below, because in North Carolina it lands on the labor too.
Maybe you're not the nineties two-story. Maybe it's a brick ranch inside the Beltline with the original single panes, a house in Oakwood, or a home you're about to list and the inspector wrote up the windows. All of those are covered here. They just don't all cost the same, and one of them isn't allowed to use vinyl at all.
One warning about the "average window replacement in Raleigh is about $6,000" figure floating around the internet. At local installer prices, $6,000 buys six to ten windows. Your house has closer to eighteen. That average describes a job that isn't yours.
Is it the window, or just the glass?
Raleigh is a young city. The median house here was built around 1996, and fewer than one in five Wake County homes predates 1980. So the classic reason to replace windows (single-pane glass leaking heat since the Eisenhower administration) mostly doesn't apply. What you have instead are builder-grade double-pane windows hitting the age where the seal between the panes lets go. Moisture gets in. The glass fogs. It never clears.
Here's the part the kitchen-table salesperson will not open with: a fogged pane is a glass problem, not a window problem. If the frame is sound, a glass shop can measure the sealed glass unit, have a new one made, and swap it into your existing sash. Raleigh shops publish prices for exactly this: one lists $198 to $480 per insulated unit with a five-year seal warranty, and another's price table runs lower for small panes. It usually takes two visits, one to measure and one to install once the unit is built.
So do the arithmetic before anyone else does it for you. Five or six fogged panes in sound frames: about $1,000 to $2,900. All eighteen windows replaced: $10,000 to $18,000. If fog is your only complaint, that's a big check to write for a fix that didn't need it.
Glass-only is the wrong answer when the trouble is the window itself:
- Rotted wood. Sills and exterior trim (the brickmould) on 1980s and 90s builder windows rot in Raleigh's humid summers. New glass in a rotting frame is lipstick.
- Sashes that won't stay open or won't lock. That's worn balances and hardware. Sometimes repairable, often a sign the whole unit is tired.
- Drafts around the frame, or sashes so loose they rattle.
- Most of the house is fogged. Once you're past half the panes, the rest are coming, and the per-window price on a whole-house job starts to look reasonable.
If you're selling, the math tilts further toward glass. Remodeling's Cost vs Value figures for Raleigh put vinyl window replacement at about 76% recouped at resale and wood at about 68%. New windows don't pay for themselves at closing. Clearing a "failed seals" line off an inspection report for a few hundred dollars a pane usually does the job.
Why the same house gets quotes $20,000 apart
This is the thing that makes window shopping feel like a prank.
A Raleigh installer publishes $500 to $800 per standard window, installed, and $7,000 to $15,000 for a 10 to 15 window job. A major manufacturer's own published installed ranges run $800 to $1,600 for vinyl and $1,100 to $2,200 for fiberglass or wood. And the Cost vs Value report prices a ten-window vinyl job in Raleigh at about $20,350, which is roughly $2,000 a window, the way a full-service remodeler would price it.
Three straight-faced sources. Ten ordinary openings. Somewhere between $6,000 and $20,000.
Scale that to eighteen openings and the gap between a local vinyl insert installer ($10,000 to $18,000) and a premium-brand, full-service quote ($20,000 to $40,000 or more) is the biggest lever on your price. Bigger than vinyl versus fiberglass. Bigger than any glass upgrade. Who you buy from moves the number more than what you buy.
Some of that gap is real. A better frame material, full-frame scope, a company with a showroom, a long warranty and a service department all cost money. Some of it is simply how the product is sold. Your job is to work out which part you're paying for, and the only way to do that is to get quotes for the same scope from different kinds of companies and line them up.
What it isn't: local labor. Construction wages in Raleigh-Cary average about $27.66 an hour against $31.42 nationally, roughly 12% lower. And the install itself is quick. A crew does 10 to 15 insert windows in a day or two, about an hour a window. On an insert job, labor on site is the smaller share of the price. The rest is product, overhead, the cost of selling it to you, and tax. So "labor is expensive here" is not a reason for a Raleigh quote to run above national ranges.
For example, based on our estimate engine, replacing 18 original builder-grade windows in a 1996 two-story in North Raleigh with white vinyl double-hung inserts, low-E glass and matching grids, keeping the existing frames and interior trim, runs about $8,500 to $14,500.
Insert or full-frame: the scope question behind every quote
Two quotes for "18 windows" can describe two different jobs. Check which one you've got.
An insert (or pocket) replacement slides a new window into your existing frame. The old sashes come out, the frame and interior trim stay. It's faster, cleaner, and the lower price: $550 to $1,000 per opening in vinyl. You lose a little glass area, because there's now a frame inside a frame. And it hides nothing. If the old frame or sill is rotten, an insert just sits on top of the rot and waits.
A full-frame replacement takes everything out down to the rough opening: frame, sill, exterior trim, sometimes interior casing. New flashing, new trim, proper sealing to the house wrap. It's the right scope when the wood is gone, and it's noticeably more: figure $900 to $1,600 per opening in vinyl, something like 40% to 60% above the insert price. On a brick-front house, expect the brick openings to cost more than the siding ones, since there's less room to work and nothing forgiving about masonry.
A decent contractor will tell you which openings need which. A mixed job (inserts where the frames are sound, full-frame on the four rotten ones on the weather side) is common and sensible. Be wary of anyone who prescribes full-frame for the whole house without having poked a single sill.
The rot question. Nobody knows what's behind the trim until the old window is out. That's fair. What's not fair is finding out the price of rot repair on install day with a hole in your wall. Ask for a written per-opening or per-foot price for rot repair before you sign.
One North Carolina wrinkle: the state code office treats an insert as a repair, while a full replacement of the window assembly has to meet the energy code (a U-factor of 0.35 or lower and solar heat gain of 0.30 or lower). In practice any window sold today beats those numbers, so this costs you nothing. The 2018 code stays in force until spring 2027 at the earliest, so nobody needs to rush you ahead of "the new code."
Vinyl, fiberglass or wood in Raleigh's climate
Vinyl
$550 to $1,000 per opening as an insert, $900 to $1,600 full-frame. This is what goes into most Raleigh subdivisions, and for an ordinary house it's the sensible default. It doesn't rot, which matters after you've watched what humidity did to your wood trim. Vinyl windows are commonly described as lasting 20 to 30 years, and the glass seal usually gives out before the frame does (you've seen that movie).
Wrong choice when: your house is in a local historic district or is a designated landmark, where it won't be approved on street-facing sides. Also think twice about dark exterior colors on a west wall in full July sun. Dark vinyl absorbs a lot of heat, and manufacturers often limit warranties on it, so read the warranty before you fall for black frames.
Fiberglass and composite
$1,100 to $2,200 per opening. Stiffer, more stable in heat, holds dark colors better, slimmer frames, and generally sold as longer-lived than vinyl. Mostly the territory of the national brands, and their quotes can run above that range.
Wrong choice when: you're fixing fogged glass ahead of a sale. With resale returning 68% to 76% on even the less expensive projects, the premium isn't coming back to you. It's a fine choice for a house you plan to grow old in.
Wood and clad wood
$1,100 to $2,200 and up per opening. The best-looking option and the one that needs the most from you. Bare exterior wood needs paint upkeep here, and rot at the sill is the classic way these fail, as your current trim may already be demonstrating. Aluminum-clad wood solves most of that outside while keeping wood inside.
Wrong choice when: low maintenance is the point and the house is a regular subdivision home. Right choice, and often the required one, in the historic districts.
The glass
Raleigh is a cooling-first climate: mild winters, long sticky summers. The standard package is double-pane low-E glass with a low solar heat gain number, and that's what a base quote should already include. If a window faces west and bakes every afternoon, a lower solar heat gain rating on that side is worth asking about.
Triple-pane is an upsell that's hard to justify here. And go easy on the energy-savings pitch in general. Going from old double-pane to new double-pane in a mild climate saves a little, and payback is typically measured in decades, not years. Replace windows because they're broken, rotten, ugly or drafty. If lower power bills are the actual goal, the money usually does more in the attic or in the HVAC system.
You also don't need hurricane impact glass. That's a coast requirement, not a Wake County one.
No permit, no federal credit, and tax on the whole thing
Three bits of Raleigh paperwork that change what a fair quote looks like.
A straight swap needs no permit
North Carolina law is unusually blunt about this. For work costing $40,000 or less on a single-family home, the state statute says no permit is required for replacement of windows, and Wake County's permit FAQ repeats it. Permit cost for a like-for-like replacement: $0. Time added: none.
You'll read elsewhere that Raleigh requires a $75 to $300 permit for this. It doesn't. So a "permit fee" line on a quote for a plain swap is worth a polite question.
Where a permit does come in:
- Making an opening bigger, adding one, or changing the header. That's structural work. The city issues the permit inside Raleigh limits, Wake County in unincorporated areas.
- Jobs over $40,000. The exemption is written for work of $40,000 or less, so a premium whole-house job above that line likely needs one. If your quote is up there, ask the city's permit office before work starts.
That same $40,000 line matters for another reason: at that price North Carolina requires the contractor to hold a general contractor license. Below it, there's no state license for window installers at all.
Which brings up the catch. No permit means no inspection. Nobody from the city will check that the glass next to your tub or on the stair landing is tempered, that the bedroom window is still big enough to climb out of in a fire, or that the flashing was done right. All of that rides on the installer. Choose accordingly, and ask about each one by name.
Sales tax hits labor too
In a lot of states, you pay sales tax on the windows and not on the work. Not here. The NC Department of Revenue's taxability chart lists window replacement as a taxable service, so the contractor charges tax on the full price, labor included. Glass repair too. Wake County's combined rate is 7.25%.
That's about $725 on every $10,000. Roughly $1,000 on a $14,000 vinyl job, $2,200 on a $30,000 premium one. Some quotes show it as a line. Some fold it in. Some mention it later. Ask whether the number is tax-inclusive, and compare quotes on the same basis, or the one that left tax off will look like a deal it isn't.
The federal tax credit is over
The federal credit for energy-efficient windows (30% of cost, capped at $600) ended. The IRS instructions say it can't be claimed for anything installed after December 31, 2025. If your windows went in by then, claim it on your 2025 return. A job done now gets nothing, and any ad or quote still dangling a federal credit is running on last year's brochure.
The state's Energy Saver NC rebates, which reached Wake County in 2026, won't rescue a window job either. They're built around heat pumps, insulation, air sealing, wiring and whole-home projects, with income limits, and windows aren't on the list. Duke Energy's rebates in Raleigh lean the same way, toward HVAC and insulation. Treat any "state window rebate" claim as something to see in writing from the program itself.
Older ranches and the historic districts
Built before 1978
The brick ranches and split-levels inside and around the Beltline are a different job: fewer, larger openings, often original single-pane wood or aluminum, and full-frame replacement is more likely. Here, new windows do make a real comfort difference.
They also fall under lead paint rules. On any home built before 1978, a company paid to replace windows must be an NC-certified renovation firm with a certified renovator on the job. Ask to see the certification. Lead-safe work means containment and careful cleanup at each opening, which adds some labor, so expect quotes on these houses to run toward the upper end of the ranges. (Doing your own windows in the house you live in is exempt, though the dust is exactly as bad for you.)
Oakwood, Boylan Heights and the other local districts
If your house is in one of Raleigh's local historic districts (Oakwood, Boylan Heights, Glenwood-Brooklyn, Prince Hall, Blount Street, Capitol Square, Moore Square) or is a Raleigh Historic Landmark, you need a Certificate of Appropriateness before you change anything outside.
The fee is the easy part. The city's fee guide puts a Minor Work application at $46 and Major Work at $242. Do the work first and ask later, and those roughly double to $94 and $473. Minor Work review takes about 10 business days. Staff can bump an application to Major Work, which waits for the monthly committee meeting.
The material rule is the expensive part. The district design guidelines say it is not appropriate to replace historic wooden window sashes with contemporary substitute materials. In plain terms: no vinyl where the street can see it. Expect to repair the original sash, add storm windows, or replace in kind with wood. Budget from the wood range ($1,100 to $2,200 per opening) upward, with true custom sash work costing more, and get that priced by someone who does old houses for a living. Add two weeks to a month or more for approval.
There's a consolation prize. North Carolina offers a 15% state income tax credit for rehabilitating owner-occupied historic homes when you spend more than $10,000 within 24 months. A $20,000 approved window project could return $3,000. The work has to meet preservation standards and be reviewed by the State Historic Preservation Office, so vinyl is out here too, and you want to talk to that office before starting, not after.
Not sure if you're in a local district? Plenty of old Raleigh neighborhoods are on the National Register without being locally regulated. Check your address with the city's historic preservation staff before you order anything.
HOAs and townhomes
Most post-1985 subdivisions and nearly every townhome community have an architectural review rule, and windows are an exterior change. Grid pattern and frame color are the usual sticking points. Get approval in writing before you order, because custom windows aren't returnable. In a townhome or condo, also ask the association who actually owns the windows. Sometimes it isn't you.
Timing: how long it takes and when to book
On site, it's quick: one to two days for 10 to 15 insert windows, two to three days for 18 to 20 or for full-frame work. The wait is beforehand. Replacement windows are made to order after someone measures each opening, and that typically takes somewhere between four and ten weeks. Ask for the current lead time, in writing, when you get the quote.
Raleigh's window season is spring. Local installers say most homeowners plan between January and May, with March the most common month to decide. Booking in late winter gets you more choice of dates. And since winters here are mild, there's no real off-limits season for installation. A crew does one opening at a time, so your house isn't open to the weather for long.
In a historic district, add the 10 business days or more for the certificate. In an HOA, ask how long architectural review takes and build that in too.
What to ask, and what should make you squint
Ask every contractor:
- Is this insert or full-frame, and is it the same for every opening? Why?
- Is sales tax in this number?
- What's your price for rot repair if you find it, per opening or per foot?
- Which windows will get tempered glass? (Near tubs and showers, beside doors, on stair landings, low to the floor.)
- Will the bedroom windows still meet egress size after the insert goes in?
- How are you flashing and sealing the exterior, and are you wrapping or replacing the outside trim?
- What exact product line is this, and what are its U-factor and solar heat gain ratings? A brand name alone tells you little. Every brand has a builder line and a good line.
- Who does the install, your own crew or a subcontractor, and who do I call in year six when a sash won't lock?
- Are you insured, and can I see the certificate? For a pre-1978 house: where's your NC lead renovation firm certification?
- Is haul-away of the old windows included?
- Will the grids and exterior color match what my HOA approved?
Squint at:
- A permit fee on a like-for-like swap. Not required at $40,000 or less.
- A federal tax credit or "state window rebate" in the pitch. The first ended with 2025. The second doesn't exist for a window-only job.
- A price that drops by thousands if you sign tonight. If the number can fall 30% because a manager got called, the first number was theater. A real price is still real on Thursday. (Contracts signed in your home generally come with a three-day right to cancel. Check your paperwork for it.)
- A quote over $40,000 from a company with no general contractor license. That's the state's line, not ours.
- Energy savings that pay for the windows in five years. Not in this climate, not from double-pane to double-pane.
- Full-frame on every opening with no inspection of the frames, or the reverse: inserts quoted over wood you can dent with a fingernail.
- A single lump sum. You want a count of openings, the product line, the scope per opening, and what's excluded.
- Whole-house replacement prescribed for a few foggy panes by someone who never mentioned that glass can be replaced on its own.
Most Raleigh window installers are small outfits doing honest work, and they're as tired of the kitchen-table circus as you are. A clear scope and a few direct questions make it easy for the good ones to give you an honest number.
For other projects on the list, the rest of our Raleigh cost guides are in one place.
Get your estimate
Want a number for your own windows? Describe the job in the box below, add a photo if you have one, and you'll get a free estimate in 2-3 minutes. If it looks right, we'll find you a vetted local window installer for the work.
Common questions
Do I need a permit to replace windows in Raleigh?
Not for a like-for-like replacement on a single-family home costing $40,000 or less. State law exempts it and Wake County confirms it, so the permit cost is $0. You do need one if you enlarge or add an opening or alter the header, and a job priced above $40,000 likely needs one too, so ask the city's permit office in that case. Historic district homes need a Certificate of Appropriateness regardless ($46 for Minor Work, $242 for Major Work).
Can I just replace the foggy glass instead of the whole window?
Usually, yes, if the frame is sound. Raleigh glass shops charge roughly $200 to $480 per insulated glass unit, so five fogged panes come to about $1,000 to $2,400. It won't fix rotted wood, broken balances or drafty frames. If those are your problems, or most of the house has fogged, replacement makes more sense.
Is there still a tax credit for new windows?
Not the federal one. It ended for anything installed after December 31, 2025. North Carolina's Energy Saver rebates don't list windows either. The one live incentive is the state's 15% historic rehabilitation credit, which applies only to qualifying historic homes, projects over $10,000, and work approved by the State Historic Preservation Office.
Do new windows pay for themselves when I sell?
No. Cost vs Value figures for Raleigh show about 76% of the cost recouped for vinyl and about 68% for wood. If you're selling and the inspection flagged failed seals, replacing just the glass in those windows is the lower-cost way to clear the report.
Is sales tax charged on window installation in North Carolina?
Yes, on the whole job. North Carolina treats window replacement as a taxable service, so the 7.25% Wake County rate applies to labor as well as materials. That's roughly $1,000 on a $14,000 job. Always ask whether a quote includes it.
Get the number for your own job
A typical job is a starting point, not your job. Describe yours (a photo helps) and the same estimate engine prices it for Raleigh in 2-3 minutes. Free, and nobody gets your number.
Sources (22)
- https://www.ncleg.gov/EnactedLegislation/Statutes/HTML/BySection/Chapter_160d/GS_160d-1110.html
- https://www.wake.gov/departments-government/permits-and-inspections/permits-and-inspections-faq
- https://ncosfm.gov/residential/110911-window-replacement-residential-buildings/open
- https://www.ncdor.gov/taxes-forms/sales-and-use-tax/taxable-items/real-property-contracts/services-real-property-taxability-chart
- https://www.irs.gov/instructions/i5695/ch01.html
- https://cityofraleigh0drupal.blob.core.usgovcloudapi.net/drupal-prod/COR15/DevelopmentFeeGuide.pdf
- https://raleighnc.gov/node/75332
- https://cityofraleigh0drupal.blob.core.usgovcloudapi.net/drupal-prod/COR10/RHDCGuidelines.pdf
- https://www.hpo.nc.gov/rehabilitation-tax-credits-owner-occupied-residential-properties
- https://www.deq.nc.gov/energy-climate/state-energy-office/energy-saver-north-carolina
- https://www.dph.ncdhhs.gov/programs/environmental-health/health-hazards-control-unit/lead/frequently-asked-questions
- https://www.bls.gov/regions/southeast/news-release/2026/occupationalemploymentandwages_raleigh_20260708.htm
- https://www.pella.com/ideas/windows/replacement-window-cost/
- https://www.jlconline.com/cost-vs-value/2025/south-atlantic/raleigh-nc/
- https://southern-energy.com/2018-ncecc
- https://www.wardandsmith.com/article/north-carolina-licensing-board-for-general-contractors-recent-enforcement-priorities-unlicensed-contracting
- https://City-Data.com/housing/houses-Raleigh-North-Carolina.html
- https://www.commerce.nc.gov/news/the-lead-feed/north-carolinas-housing-stock
- https://raleighwindowcompany.com/window-installation-faqs/
- https://wowfix.us/foggy-window/raleigh-nc/
- https://argowindowrepair.com/north-carolina/window-repair-raleigh/window-glass-replacement-raleigh
- https://www.gatsbyglass.com/the-triangle-nc/about/blog/categories/company/how-to-tell-if-your-window-glass-needs-repair-or/
Researched for Raleigh, NC · Updated November 18, 2026 · How these guides are made
Prices are researched local ranges, not quotes. The contractor who sees your job sets your actual price. More Raleigh cost guides