HVAC Replacement Cost in Olathe, KS (2026 Furnace + AC Prices)
The short answer
Here's the likely situation. Your Olathe house was built somewhere between 1985 and 2010. The original system got swapped out once already, probably around 2008 to 2015. That replacement is now 10 to 18 years old, and lately the AC has been making the noise. Or the furnace quit on the first cold night. Or a hailstorm chewed up the condenser fins. Or you're buying the place and the inspector wrote "near end of life" in a tone you didn't love.
Whatever brought you here, the number is about the same:
Replacing a gas furnace and central AC together in a typical Olathe home (2,200 to 2,800 sq ft, basement furnace, 3.5 to 4 tons, existing ducts) runs about $10,000 to $13,000 for entry-level equipment, $14,000 to $17,000 for a mid-tier high-efficiency system, and $20,000 or more for the top tier. Those figures come from what Kansas City contractors publish, and they include equipment, labor, permit and haul-away.
Furnace only: roughly $4,900 to $11,000 depending on efficiency. AC only: roughly $5,500 to $9,500 now that the indoor coil usually has to come along. More on why below.
What a furnace and AC swap costs in Olathe
Most Olathe jobs are the boring kind, and boring is good. Furnace in the basement, condenser on a pad out back, ductwork that's been fine for 20 years. That's the job these ranges describe.
Entry tier, about $10,000 to $13,000. An 80% efficient single-stage furnace and an entry-level AC (the 13.4 to 14.3 SEER2 class). It works. It's the cheapest way to get heat and cold air back. It also misses the Evergy rebate entirely (more on that later) and keeps the less efficient furnace for another 15 to 20 years.
Mid tier, about $14,000 to $17,000. A 95% or 96% condensing furnace with a two-stage burner and an AC around 16 SEER2. This is where most people who plan to stay in the house land, and in Olathe it's an easier step up than in a lot of places, because of where your furnace lives.
Top tier, $20,000 and up. Variable-speed furnace, 18+ SEER2 AC, a communicating thermostat, sometimes zoning. Quieter, more even temperatures, nicer upstairs bedrooms in July. Worth it for some houses. Not a requirement for comfort.
For example, a 1999 two-story in Olathe with about 2,600 sq ft plus a finished basement, swapping an 80% furnace and a failing 4-ton AC for a 95%+ furnace and a matching central AC on the existing ducts, comes out at about $8,500 to $15,000 in our estimate engine. That's below the mid-tier guide figure mostly because the example asks for a 95% furnace and a matching AC, not specifically the two-stage, 16 SEER2 package the guides price as mid-tier.
Two things push every one of these numbers up right now.
Equipment keeps getting more expensive. The federal producer price index for heating and AC equipment is up about 9% in the last two years and about 61% since 2019. Manufacturers raised prices twice in 2026, and at least one big one has said plainly it will keep doing it. So any cost guide written on 2022 numbers is quietly 15% or more too low before anyone touches a wrench. If the price you found online looks great, check the date on it.
Quotes for the same job spread wide. Kansas City homeowners have reported quotes from about $7,000 to $20,000 for what looked like the same system. Part of that is real scope (a new line set, a coil, a vent conversion), part is brand, and part is overhead. Get the scope written down line by line and the spread usually makes more sense.
Bigger houses cost more, and two-system houses cost a lot more. A larger two-story or a 1.5-story with a bonus room often has a second system in the attic. Budget roughly a second system on top, and expect the attic one to take more labor. Add-ons like a new thermostat, humidifier, media filter, UV light or surge protector typically add $200 to $1,500.
Just the AC isn't just the AC anymore
This is the part that surprises people who replaced an AC ten years ago and remember it being a one-box job.
New central ACs no longer use R-410A. They use A2L refrigerants (R-454B or R-32), which are mildly flammable, so the rules around them are stricter. A new A2L condenser has to be matched to an A2L-rated indoor coil, and that coil usually carries a refrigerant leak sensor that gets wired to the furnace. Code officials treat a new A2L outdoor unit hooked to your old R-410A coil as a mismatched, non-compliant system, and manufacturers say flatly there's no drop-in or retrofit. So "replace the AC" now usually means condenser plus indoor coil plus line-set work, roughly $5,500 to $9,500 in a typical Olathe house. Your existing copper lines can often be reused, but only if they're the right size, flushed and pressure-tested. A good installer tells you which one you're getting and why.
Then the plot twist. In 2026 the EPA dropped the installation deadline for R-410A split equipment built before 2025. So some contractors can still sell you a leftover R-410A condenser that matches your existing coil, and that will cost less today. The catch is down the road: nobody is making new R-410A systems, R-410A production is stepping down hard through 2036, and the industry expects refrigerant prices to keep rising. A repair that needs a few pounds of refrigerant in 2032 could sting. Fine for a house you're selling soon. Less fine for a system you expect to run another 15 years.
And if your furnace is 12 or more years old too, an AC-only job often stops making sense. You're paying for a new coil, a leak sensor hookup and a labor day anyway. Doing the furnace at the same time usually costs less than doing it separately in a few years.
Hail is a real reason people end up here. 2026 was a rough storm year around Olathe, with 1.75-inch hail reported southwest of town in April and more storms across Johnson County through the summer. The Kansas Insurance Department put out a storm-claims notice for the county. If your condenser took a beating, it may be an insurance claim. One thing to raise with your adjuster early: once leftover R-410A stock dries up, a damaged R-410A condenser may not be replaceable like-for-like, which turns a "condenser" claim into a "condenser plus coil" claim. Ask your contractor to write that out plainly in the estimate.
The furnace: 80% or 95% in an Olathe basement
About 90% of Olathe's homes were built in 1970 or later, and the typical one has the furnace in a basement. That matters more than it sounds.
An 80% furnace (about $4,900 to $7,200 installed on its own) vents up the existing metal flue or chimney, often shared with the water heater. It's the cheaper box and it's still legal to install. A federal rule requiring 95% minimum efficiency for most gas furnaces is scheduled for December 2028, and the gas industry has asked to push it back, so that date may move. Nobody is coming to take your 80% furnace away in the meantime.
A 95% to 98% condensing furnace (about $7,500 to $11,000 on its own, more in big houses) vents through PVC pipe out a side wall and drains condensate water. In an attic that can be fiddly. In a basement, the rim joist and a floor drain are usually a few feet away, so in Olathe the step up is mostly the equipment premium, roughly $2,500 to $4,000 in local contractor pricing, plus some pipe.
Kansas gas isn't cheap either. Atmos Energy, which serves Olathe, got a rate increase in March 2026, and the Kansas average residential gas price was around $14.81 per thousand cubic feet in 2025. Over 15+ years, 15 points of efficiency adds up in a house that runs the furnace a lot.
The hidden cost to ask about: the orphaned water heater. When the old furnace leaves the shared flue, the gas water heater is now venting alone up a chimney sized for two. That can cause poor draft and condensation in the flue. The fix might be a flue liner, or a new water heater if yours is old anyway. A good contractor checks this before quoting. Ask whether yours did.
When 80% is the right call: you're selling in the next few years, or the house is small and tight and barely uses gas. Otherwise, in an Olathe basement, 95% is usually the easy upgrade.
Heat pumps and dual fuel on Evergy rates
A heat pump is an AC that also runs backwards in winter. Here, the smart setup for most gas homes is dual fuel: a heat pump takes the AC's spot outside, and the gas furnace stays as backup for the cold days. Kansas City contractors price dual fuel systems at roughly $13,000 to $19,500.
The math on Evergy's 2026 Kansas Metro rates goes like this. Winter electricity, with riders, runs about 11 cents a kWh. A 95% gas furnace delivers heat for roughly $15 per million BTU. A heat pump running at a COP of 2.5 (a mild winter day) does it for about $13. At COP 3, about $11. On a single-digit morning, when a heat pump drops toward COP 1.5, it's more like $22, and gas wins easily. The crossover sits around COP 2.2.
So a heat pump with gas backup saves you a bit on mild days, and the furnace takes over when it's cold. Expect modest savings, likely low hundreds of dollars a year at most for a typical home. Heat pump equipment prices have flattened lately while the rest of the HVAC price index climbed, which helps the case a little. An all-electric heat pump with electric resistance backup is usually a poor fit for a gas house here.
Dual fuel is the wrong call if your electrical panel can't take it without an upgrade, or if nobody's going to set up the thermostat with a sensible switchover temperature.
Mini splits (the wall-mounted ductless units) make sense for a finished basement that's always cold, a bonus room over the garage, or an addition the ducts never reached. Prices vary too much by room and setup to give a fair local range. Before you buy one, ask whether a damper adjustment or duct balancing would fix the room for a lot less.
The money back: Evergy, and not much else
Short version: for most Olathe homeowners in 2026, Evergy is the only rebate in town.
- The federal tax credit is gone. The 25C credit, which used to give up to $600 on a furnace or AC and $2,000 on a heat pump, doesn't apply to anything placed in service after December 31, 2025. If a quote mentions it, ask them to update the quote.
- The Kansas home energy rebates (HEAR and HER) aren't open yet. There's no firm launch date, and the state's own rebate FAQ says rebates won't be paid retroactively. Waiting only makes sense if your household is income-qualified and your system still runs.
- Evergy pays $400 to $600 for a central AC that replaces an existing AC: $400 at 15.2 to 15.99 SEER2, $500 at 16 to 16.99, $600 at 17+. Heat pumps get $500 to $1,000 depending on efficiency. Mini splits get $150, in limited cases. The equipment has to be AHRI-certified and the installer has to be an Evergy Trade Ally. Those levels run through the end of 2027.
- Entry-level ACs get nothing. The 13.4 to 14.3 SEER2 units under the rebate line are cheaper upfront, but you leave the rebate on the table.
- Gas rebates: You'll see a furnace rebate from Atmos listed on some websites. If a contractor says you'll get one, ask them to show you the current program page.
One gray area: if you're adding a heat pump to a gas-furnace house, it isn't always clear which Evergy rebate line applies, the AC level or the heat pump level. Ask your installer to confirm with Evergy before you sign, not after.
If money is tight, the Kansas Weatherization Assistance Program serves households at or below 200% of the federal poverty level (about $53,000 for a family of four). The work is free. Whether it covers a furnace depends on the home energy audit, so call and ask.
Permit, license and the sales tax line
Three small things that are easy to check and say a lot about a quote.
The permit is cheap. Olathe requires an Individual Trade Permit for a furnace or AC replacement, with inspections. The city's 2026 fee schedule sets it at $50 for the first $10,000 of project cost plus 0.5% above that. A $15,000 system pulls a $75 permit. A $20,000 one, $100. If a quote has a $150 to $300 "permit" line, most of that is the contractor's admin time, which is fine to charge for, but it should be called what it is. Work started without a permit that gets caught pays double the permit fee. The bigger issue: an unpermitted install has no inspection, and that tends to come up when you sell.
The license is county-level. Kansas has no statewide HVAC license. In Johnson County, HVAC work falls under a Class DM Mechanical Contractor license, which requires an exam or education, liability insurance and workers' comp. A general residential contractor license doesn't cover HVAC. Look anyone up on the county contractor search in about a minute.
There usually shouldn't be sales tax on labor. Kansas exempts labor for repair or replacement work on a residence. The contractor pays sales tax on materials when buying them and builds it into the price. So a residential replacement quote with sales tax added to the labor deserves a question. (A job written up as a retail equipment sale with installation can be taxed differently, so ask how they've set it up.)
When to do it
November is a decent month. Heating season has started but hasn't peaked, and AC season is long gone. Installers are busiest in July and August when ACs die, and again during the first real cold snap when furnaces quit. If your system is limping but still running, scheduling now beats an emergency call at 9 p.m. in January when you take whoever answers.
A straight swap is usually one day. A furnace and AC with a 95% vent conversion or new line set can stretch to two. Standard equipment is generally stocked around Kansas City, so the wait is more about the schedule than the parts.
Because equipment prices keep climbing, a quote from six or twelve months ago may not hold. Ask how long the price is good for.
What to ask, and what to squint at in a quote
Good contractors will answer all of these without breaking a sweat. Write the answers down.
- Is the indoor coil included, and what refrigerant is the new system? If the AC is new, the coil should be in the scope. If they're quoting R-410A, ask why and how long they expect refrigerant to stay affordable.
- Are you reusing my line set? Did you check the size, and will you flush and pressure-test it?
- For a 95% furnace: where does the PVC vent go, where does the condensate drain, and what happens to my water heater's venting?
- Did you size it, or match the old one? A proper load calculation (often called a Manual J) takes into account your windows, insulation and layout. Plenty of 2010 systems were oversized. Bigger isn't better: an oversized AC short-cycles and leaves the house clammy.
- Does this system qualify for the Evergy rebate, and are you a Trade Ally? Get the SEER2 rating and the AHRI certificate number on the quote.
- Is the permit in the price? What's your Johnson County license number?
- What's the warranty, and who handles it? Equipment warranties often need registration within a set window. Labor warranties vary a lot by company. Ask for both in writing.
Red flags worth a second look:
- A price over the phone without anyone looking at the house. Fine for a ballpark. Not for a contract.
- "Just the condenser" on an A2L system hooked to your old coil. That's the mismatch the rules say no to.
- A federal tax credit in the math. It's gone for 2026 installs.
- No mention of a permit, or an offer to skip it to save a few dollars.
- Sales tax on the labor line of a residential replacement.
- Pressure to sign today because the "special" ends tonight. Equipment prices are going up, sure. They're not going up at midnight.
Get your estimate
Want a number for your own furnace and AC? Describe the job in the box below, add a photo of the equipment label if you have one, and you'll get a free estimate in 2-3 minutes. If it looks right, we'll find you a vetted local HVAC contractor for the work.
Common questions
Should I repair or replace a 15-year-old system in Olathe?
If the repair is small (a capacitor, an igniter, a contactor), repair it. If the AC needs a compressor or a refrigerant leak fix on an R-410A system that's 12 or more years old, replacement usually wins, because refrigerant is only getting more expensive and the new coil requirement means you'll pay for that work eventually anyway. A furnace with a cracked heat exchanger is a replace, not a repair.
Can I replace just the AC and keep my furnace?
Usually, yes. With a new A2L system, though, the indoor coil above the furnace typically gets replaced too, and the coil's leak sensor gets wired to the furnace. Expect roughly $5,500 to $9,500 in a typical Olathe home. If the furnace is also 12+ years old, get a price for both at once before deciding.
Will homeowners insurance cover a hail-damaged AC?
Often, if the damage is from a covered storm and you file within your policy's window. Get the contractor to document the damage with photos and write down whether the replacement needs a new coil because of the refrigerant change, since that can double the claim. Your deductible still applies.
Should I wait for the Kansas state rebates?
Only if your household is income-qualified and your current system still works. The state program has no firm launch date, and rebates won't be paid for work done before it opens. If your system has failed, Evergy's $400 to $1,000 rebate is the realistic money back right now.
How long does an HVAC replacement take?
A straight furnace and AC swap is usually one day. Converting to a 95% furnace or running a new line set can make it two. Add a little time for the city inspection, which your contractor schedules.
Get the number for your own job
A typical job is a starting point, not your job. Describe yours (a photo helps) and the same estimate engine prices it for Olathe in 2-3 minutes. Free, and nobody gets your number.
Sources (29)
- https://dickray.com/how-much-is-a-new-residential-hvac-system-in-kansas-city/
- https://growthzone.leawoodchamber.org/news/Details/leawood-furnace-replacement-cost-guide-2026-edition-300148
- https://cca.lschamber.com/news/Details/what-lee-s-summit-homeowners-should-expect-to-pay-for-a-furnace-in-2026-302392
- https://fred.stlouisfed.org/data/PCU333415333415.txt
- https://fred.stlouisfed.org/data/PCU333415333415H
- https://www.achrnews.com/articles/166689-price-increases-remain-part-of-the-residential-hvac-outlook
- https://www.achrnews.com/articles/166226-epa-removes-r-410a-installation-deadline
- https://www.nahb.org/blog/2026/05/epa-hvac-refrigerants-r-410a-final-rule
- https://www.ncosfm.gov/mechanical/03041-properly-matched-partial-replacement-split-system-heat-pump-or-air-conditioner-a2l-refrigerant/open
- https://www.bosch-homecomfort.com/us/en/residential/knowledge/a2l-refrigerant-change-guide
- https://www.govinfo.gov/content/pkg/FR-2026-04-27/html/2026-08145.htm
- https://nces.ed.gov/Programs/Edge/ACSDashboard/2010140
- https://curb.kansas.gov/curb_news/EKME_Rates26_07072026.pdf
- https://www.eia.gov/dnav/ng/hist/n3010ks3a.htm
- https://www.kcc.ks.gov/news-2-26-26
- https://www.kctv5.com/2026/03/01/atmos-energy-rate-hike-kicks-what-it-means-kansans-monthly-bills/
- https://www.irs.gov/newsroom/faqs-for-modification-of-sections-25c-25d-25e-30c-30d-45l-45w-and-179d-under-public-law-119-21-139-stat-72-july-4-2025-commonly-known-as-the-one-big-beautiful-bill-act-obbb
- https://kshomerebates.gov/faq/
- https://www.qat1.evergy.com/-/media/documents/ways-to-save/discounts/kansas-rebate-incentive-chart.pdf
- https://www.herculesindustries.com/ASSETS/DOCUMENTS/CMS/EN/LG_REBATES_2026/Evergy%20rebates%20for%20Lenexa%20team.pdf
- https://kshousingcorp.org/weatherization-assistance
- https://www.olatheks.gov/government/building-codes/licenses-permits/residential-building-and-development
- https://www.olatheks.gov/home/showpublisheddocument/23023/639033740077100000
- https://jocogov.org/department/contractor-licensing/license-types
- https://cls.jocogov.org/clsCourseReg/searchcontractor.aspx
- https://www.ksrevenue.gov/pub1525.html
- https://haildrive.com/storms/ks-johnson-2-sw-olathe-2026-04-26
- https://www.insurance.kansas.gov/home/showpublisheddocument/4692/639089935528430000
- https://reddit.sentinel-team.org/posts/1pejqff/snapshots/2025-12-05T12%3A11%3A29.356408Z
Researched for Olathe, KS · Updated November 11, 2026 · Reviewed by Ralph Cockburn on November 16, 2026 · How these guides are made
Prices are researched local ranges, not quotes. The contractor who sees your job sets your actual price. More Olathe cost guides