Window Replacement Cost in Maple Grove, MN (2026)
The short answer
You probably know the scene. A 1990s two-story, the builder's original wood casements, about 30 years old now. A few have gone foggy between the panes. A crank or two spins without doing much. Every January there's frost on the bottom of the sash, and lately one of the sills gives a little when you press it. Maybe you're here for a different reason (hail chewed up the cladding, you're getting the house ready to sell, or only one window is the problem). The numbers below still apply, you'll just use a smaller piece of them.
For a typical Maple Grove home with about 18 window openings, mostly casements plus an arched or half-round unit, insert replacement installed by an independent contractor runs roughly:
- Vinyl: $13,500 to $23,000 ($750 to $1,300 per opening)
- Fiberglass or composite: $18,000 to $31,000 ($1,000 to $1,700 per opening)
- Clad wood, like for like with what you have: $23,000 to $41,000 ($1,300 to $2,300 per opening)
Tearing out the old frames (full-frame) adds about $150 to $400 per opening, plus whatever rot turns up. If the national "$300 a window" figures you've seen made this look like a $6,000 job, they were built on smaller houses full of double-hungs. That isn't your house.
Why your windows cost more than the "average window"
Maple Grove's median home was built in 1991 (per Census figures), and the builders of that era loved casements. Casements cost more than double-hungs at every step: more hardware, more glass per opening, a crank operator, and more fussing to get the sash to seal. Twin Cities installers price casements around $600 to $1,400 each, against roughly $450 to $1,100 for double-hungs. Just the product for a clad-wood casement runs about $500 to $1,500 per opening before anyone picks up a drill. A single Andersen 400 casement lists around $513 to $697 depending on size, and a venting double casement climbs past $1,100, and close to $2,000 at the big end with grilles.
Then there's the half-round over the front door. Arched and half-round units are custom-made, and they're often the most expensive single line on the quote, commonly priced at around one and a half to three times a standard opening. If yours is fixed (doesn't open) and the glass is clear, ask for a price with it left in place. Some homeowners keep a sound specialty unit and replace only the ones that open.
Labor is the other piece. Construction wages in the Minneapolis-St. Paul metro run about 20% above the national average, per federal wage data. Expect about $300 to $600 per opening for an insert and $500 to $800 for full-frame. What pushes it up here:
- second-story windows and the tall back wall of a walkout, which mean ladders, staging or a lift
- stained oak trim and wood jambs that have to come off and go back cleanly
- winter work, done one opening at a time so the house doesn't freeze
For a sense of the high end: the national remodeling cost survey priced ten replacement windows in Minneapolis at about $23,000 for vinyl and $26,000 for wood in 2024. That assumes a remodeler running the job with new trim and full markup, so treat it as the ceiling, not the typical quote.
Vinyl, fiberglass or clad wood
Vinyl ($750 to $1,300 per opening here). A good welded-frame vinyl window typically lasts 20 to 30 years. It's the best value per dollar if the house isn't trimmed in stained wood. It's the wrong choice when you have honey-oak trim and wood jambs and want wood inside, because vinyl interiors look like vinyl. It's also limited on big or odd shapes, so the half-round may come back in a different material or at a surprising price. Dark vinyl colors move more with Minnesota's temperature swings, so ask how the frame is reinforced if you want anything darker than white or tan.
Fiberglass or composite ($1,000 to $1,700 per opening). This is the middle lane: think Andersen 100 (Fibrex), Marvin Elevate or Pella Impervia class. It's stiffer than vinyl, has narrower frames so you get a little more glass, and handles the cold well. Expect 30-plus years, with warranty terms that vary by brand. It's wrong when an HOA or your own taste demands a real wood interior, or when the budget only stretches to vinyl.
For example, based on our estimate engine, a 1996 Maple Grove two-story replacing all 18 original Andersen wood casements, including a half-round over the front door, with mid-range vinyl or fiberglass inserts (a few fogged units, a couple of soft sills, siding and trim kept) runs about $14,500 to $25,000.
Clad wood ($1,300 to $2,300 per opening). Most 1990s Maple Grove homes already have this (Andersen 400, Pella, Marvin class), so it's the like-for-like match that keeps your interior looking the way it does. Expect 30-plus years, if you control indoor humidity. That condition matters. Look at how your current windows failed. Rot at the bottom rail usually comes from winter condensation running down the glass, and a new wood window in the same house with the same humidity will fail the same way. If your sills rotted, run a dehumidifier or fix the ventilation first, or pick a frame that doesn't rot.
The glass spec, the $50 rebate and the credit that's gone
The 30% federal tax credit is over. It covered windows up to $600 a year, and it ended for anything installed after December 31, 2025, under the 2025 federal tax law. Signing a contract or paying a deposit in 2025 doesn't count, installation does. Any quote or ad that still mentions the federal window credit for a 2026 install is wrong, and it tells you how carefully the rest of the paperwork was read.
What's left is the gas utility rebate. If your gas comes from CenterPoint (most Maple Grove homes heat with gas, but check your bill), CenterPoint's window rebate pays $50 per qualifying window. The fine print:
- the window has to meet ENERGY STAR's Northern spec: U-factor of 0.22 or lower and SHGC of 0.17 or higher
- it has to go into heated living space, so basement windows don't count
- an eligible installer has to install it, so DIY doesn't qualify
- the paperwork is due by December 31 of the year it's installed
That U-0.22 number is tough. Andersen itself says few double-pane products hit it and triple pane is the simplest way there. Getting the better glass typically adds about $55 to $105 per window at the manufacturing level, and Twin Cities installers quote $100 to $400 per window for the upgrade. So on 18 windows the rebate tops out at $900, which roughly covers the glass upgrade at the low end. It does not make triple pane free. Buy the better glass because you want warmer windows and less frost, not for the rebate.
If you're installing in the last weeks of the year, ask the installer whether they file the rebate for you (there's an instant-rebate route that pays the installer) and make sure the job finishes before December 31.
Soft sills change the job
This is the decision that matters most on a 30-year-old Maple Grove house, and it's the one most quotes skip.
An insert (pocket) replacement leaves the old frame in the wall and slides a new window inside it. Siding and interior trim stay put. It costs less and it's fast. A full-frame replacement takes everything out down to the rough opening, so the installer can see the sheathing, fix rot and flash the opening properly.
Here's the local wrinkle: Minnesota window installs didn't commonly use pan flashing (a waterproof tray under the window) until around 2006, according to a Twin Cities home inspection firm. Your 1990s openings almost certainly have none. An insert can look perfect on install day while rot keeps going underneath, and that firm has seen it show up years later, during a buyer's moisture test. That's an unpleasant way to find out, at an unpleasant moment.
What to do with that:
- If sills are soft, ask the installer to probe them during the estimate, not after you've signed.
- If there's real rot, get a full-frame price for those openings. On 18 openings, full-frame everywhere adds roughly $2,700 to $7,200 before repairs. Doing just the bad ones costs a lot less.
- In both cases, get a written unit price for rot repair in the contract (per sill, per square foot of sheathing), so a surprise doesn't turn into whatever number shows up on the change order.
If the frames are solid and dry, inserts are a perfectly good choice. The point is to know which situation you're in before the job starts.
When fixing beats replacing
If only a handful of windows are fogged and the frames are solid, you might not need a single new window.
- Glass-only swaps. A glass shop can replace the sealed glass unit in a fogged window, typically for a few hundred dollars per unit, less per unit if you do several at once.
- Factory replacement sashes. Andersen sells new 400 Series casement sashes. A common size runs $634 plus $38 for clips, plus labor, and ships in about 8 business days. The catch for Maple Grove: that listing is for units from 2013 on, so 1990s windows need a compatibility check before you count on it. Ask a dealer to identify your units (the model info is usually etched in a corner of the glass).
What a repair won't do: fix drafts, rot, worn cranks on every window, or a poor energy rating, and it earns no rebate. It's a good answer for "three foggy windows in a sound house." It's the wrong answer for "every sill is soft."
Same windows, quotes twice apart
Checkbook's undercover shoppers in the Twin Cities found the highest quote more than double the lowest for identical windows, and $50 to $100 per window differences for the same brand. On 18 windows, that spread can be $15,000 to $25,000. Same glass. Same house.
Part of that is the metro itself. Andersen is based in Bayport and Marvin in Warroad, so this area is packed with branded dealers and in-home sales teams. The in-home model usually starts from a high list price and then knocks a big chunk off: buy-one-get-one deals, a percentage off "today only," 18 months of deferred interest. The discount is measured from a list price nobody pays. Deferred interest charges you all the back interest if any balance is left when the promo ends. The only comparison that means anything is the final price for the same windows, same glass and same install method, across at least three quotes. In-home brands are often well above independent installers on the same type of window, so if one of your quotes sits far above the ranges at the top of this page, that's usually why.
One more protection: Minnesota gives you three business days to cancel a contract signed at your home, and the clock doesn't start until you get written notice of that right. If someone pushes you to sign at the kitchen table, you can. And then you can change your mind.
Permits, tax and the small lines
Yes, Maple Grove wants a permit for window replacement. Some cost sites say a same-size replacement doesn't need one. The city disagrees, and it has a fee for it. The 2026 fee schedule sets a flat window or door replacement permit at $50 for one unit or $75 for two or more, plus a $1 state surcharge. The same fee applies to townhouses. It goes through the city's online permit system, and your installer should pull it and put it on the quote. A whole-house job comes to $76 in permit fees. If someone tells you permits are optional, take note of that too.
If your address has an Osseo, Champlin or Plymouth ZIP, check which city you're actually in, because the permit follows the city line, not the mailing address.
No sales tax line. Maple Grove's combined rate is 9.025%, but on an installed job the contractor pays tax on the materials and builds it into the price, and installation labor isn't taxed. If a lump-sum install quote adds 9% on top of the total, ask why. You'd only pay that rate yourself if you buy windows to install on your own.
Basement egress is a different animal. Replacing an existing window is exempt from the modern egress size rules, as long as the new one is the largest standard size that fits and opens the same way or wider. Cutting a new egress window for a basement bedroom is a separate project, typically around $2,000 to $6,000 or more with the well, and the state egress rules require a compliant opening and a well of at least 9 square feet. It's permitted by project value, roughly $200 or so in city fees for a $5,000 job.
Hail, siding and insurance
Maple Grove gets hail. The August 2019 storm dropped golf-ball hail across Maple Grove and Brooklyn Park, and one exterior contractor fielded 15 to 20 calls an hour, with crews booked right up to winter.
If hail damaged your cladding, screens or glass, part of the window work may be claimable, so call your insurer before you sign anything with a window company. And if your siding is coming off for a claim anyway, the insert-versus-full-frame question mostly answers itself: with the siding off, a full-frame install with proper flashing costs much less extra than it normally would. That's two permits (siding is a separate $100 permit), about $176 total. If the roof is part of the same claim, our Maple Grove roof replacement guide covers that side.
After a storm, expect busier crews, longer waits and more door-knockers. The three-day cancellation right above applies to them too.
Timing: prices, lead times and winter
If you have a quote from 2024 or 2025, it's probably 5 to 10% low now. Every major brand raised prices in the past year: Marvin about 5% (December 2025), Andersen across the board (June 2026), Pella 3 to 4% (July 2026), and several vinyl makers 3 to 8%. Aluminum, which goes into clad-wood cladding, spacers and hardware, jumped about 30% in a year after the 2025 tariffs. Ask for a fresh quote rather than holding an installer to an old one.
Lead times: windows are made to order, so expect several weeks between signing and install, often longer for specialty shapes and triple pane. The actual install on 18 inserts usually takes 1 to 3 days. Full-frame with siding work takes longer.
Winter is fine. Good installers work year-round in Minnesota and swap one opening at a time, so each hole is open for minutes, not hours. Spring, fall and post-hail months are the busy stretches. Winter can mean easier scheduling.
What to ask, and red flags in a quote
Ask every installer:
- Is this insert or full-frame, opening by opening? If insert, did you check the sills?
- What's your written price for rot repair if you find it?
- What's the exact product line, frame material and glass package? Does it meet U-0.22, and will you file the CenterPoint rebate?
- How are you handling the half-round, and what's the price with it left in place?
- Are you pulling the Maple Grove permit, and is it in the price?
- How will you finish the interior: jamb extensions, trim, stain match?
- In bedrooms, are you keeping casements (or something that opens at least as wide)? Swapping a casement for a slider or double-hung can shrink the escape opening.
Red flags:
- A federal tax credit for a 2026 install.
- "No permit needed in Maple Grove."
- A price that's only good if you sign tonight, or a discount off a list price you never saw.
- A lump-sum install with sales tax added on top.
- Glass described as "energy efficient" with no U-factor.
- No mention of what happens if they find rot.
- Financing pitched before the window price is clear.
Get your estimate
Want a number for your own windows? Describe the job in the box below, add a photo if you have one, and you'll get a free estimate in 2-3 minutes. If it looks right, we'll find you a vetted local window installer for the work.
Common questions
Do I need a permit to replace windows in Maple Grove?
Yes. The city charges a flat $50 for one window or door and $75 for two or more, plus a $1 state surcharge. Your installer normally pulls it and includes it in the quote. Siding work on the same house is a separate $100 permit.
Is there still a tax credit for new windows in 2026?
No federal one. The 30% credit ended for windows installed after December 31, 2025. CenterPoint customers can get $50 per window if it meets the U-0.22 Northern spec, is installed by an eligible installer in heated living space, and the paperwork is in by December 31 of the install year.
Should I replace all my windows or just the fogged ones?
If the frames are sound and only a few are fogged, a glass-only swap or a factory replacement sash can cost a few hundred dollars per window instead of $1,000 or more. If sills are soft, cranks are failing and you get frost every winter, whole-house replacement usually makes more sense, and it's worth checking the openings for rot before choosing insert or full-frame.
Can I swap my casements for double-hungs or sliders to save money?
Sometimes, but be careful in bedrooms. Minnesota lets replacement windows skip the modern egress size rules only if the new window opens the same way or wider. A double-hung or slider in a casement opening usually opens less, so keep casements (or another style with an equal or bigger opening) in sleeping rooms.
How long does window replacement take in Maple Grove?
Plan for several weeks of lead time after you order, longer for arched shapes and triple pane. The install itself is usually 1 to 3 days for about 18 insert windows. Crews work through winter, swapping one opening at a time.
Get the number for your own job
A typical job is a starting point, not your job. Describe yours (a photo helps) and the same estimate engine prices it for Maple Grove in 2-3 minutes. Free, and nobody gets your number.
Sources (25)
- https://city-stats.com/minnesota/maple-grove/housing
- https://www.maplegrovemn.gov/716/Fee-schedule-PDF
- https://www.maplegrovemn.gov/491/Building-permit
- https://www.revenue.state.mn.us/sites/default/files/2026-08/metro-tax-rate-guide-2026-q4.pdf
- https://www.revenue.state.mn.us/sites/default/files/2023-01/FS152.pdf
- https://www.revenue.state.mn.us/sites/default/files/2023-01/FS150.pdf
- https://www.centerpointenergy.com/en-us/residential/save-energy-money/efficiency-programs-and-rebates/window-rebates?sa=mn
- https://instead.com/resources/blog/what-section-70505-ended-for-the-25c-home-energy-credit
- https://www.andersenwindows.com/for-professionals/pro-views/energy-star-7-update
- https://neea.org/wp-content/uploads/2025/03/Study-of-High-Performance-Windows-Incremental-Manufacturing-Cost.pdf
- https://www.dli.mn.gov/sites/default/files/pdf/fs-emergency-escapes.pdf
- https://www.ag.state.mn.us/consumer/publications/CoolingOffPeriod.asp
- https://www.bls.gov/regions/midwest/news-release/occupationalemploymentandwages_minneapolis.htm
- https://www.checkbook.org/twin-cities-area/window-installers/articles/How-to-Choose-a-Window-Installer-5584
- https://www.jlconline.com/cost-vs-value/2024/mountain/minneapolis-mn/
- https://cmwindowsanddoors.com/products/andersen-windows-400-series-casement-24-wide-vinyl-exterior-wood-interior-new-construction-low-e4-glass-full-screen-included-c13-c135-c14-c145-c15-c155-or-c16
- https://parts.andersenwindows.com/detail_1348175__w_casement_sash.html
- https://www.universalsupply.com/?p=5940
- https://www.universalsupply.com/?p=5968
- https://www.agc.org/index%2ephp/news/2026/01/30/double-digit-increases-aluminum-steel-and-copper-costs-drive-producer-price-indexes-construction
- https://structuretech.com/window-replacements-its-not-just-about-the-windows/
- https://www.startribune.com/repairing-a-window-with-fogged-glass/359443641
- https://ccxmedia.org/news/contractors-busy-after-hail-damages-brooklyn-park-maple-grove-homes/
- https://owlroofing.com/blog/cost-of-window-replacement-in-minnesota/
- https://wgccinc.com/blog/window-replacement-cost-minnesota-2026
Researched for Maple Grove, MN · Updated November 20, 2026 · How these guides are made
Prices are researched local ranges, not quotes. The contractor who sees your job sets your actual price. More Maple Grove cost guides