Water Heater Replacement Cost in Johns Creek, GA (2026)
The short answer
You live in a Johns Creek house built somewhere around 1995. The water heater in the basement or garage is the second one the house has had, maybe the third, and it has picked this week to leak from the bottom. Or it hasn't yet, and you'd like to deal with it before it ruins a Saturday. Or you're tired of the upstairs shower going cold and you're wondering about tankless. Same guide for all three.
A standard 50-gallon gas tank, installed in a Johns Creek basement or garage with the permit and the code items, runs about $1,800 to $3,200. A small licensed plumber can land near $1,300 to $1,800 when little needs updating. The big advertised brands quote $3,500 to $5,400 for the same tank.
A gas tankless conversion runs about $4,000 to $7,000. The easy ones, with a short gas run, come in closer to $3,000 to $4,000.
The other versions, quickly:
- 40-gallon gas tank: about $100 to $200 less than the 50.
- Tank in the attic or an upstairs closet: add roughly $300 to $800.
- Electric tank, 40 to 50 gallons: about $1,400 to $2,600.
- Heat pump water heater: about $3,500 to $6,000 before rebates.
- Two tanks on one visit: roughly double, less a few hundred dollars.
Those are installed prices, with haul-away of the old one. Now the reasons, because a $1,900 quote and a $4,800 quote for the same basement deserve an explanation.
The tank is about $900. The rest is where quotes split.
Walk into a big-box store and a 50-gallon, 40,000 BTU natural gas tank with a 6 or 9 year warranty is $849 to $959 on the shelf. That is the tank your plumber is most likely installing, or a close cousin from the supply house.
So the tank is somewhere between a quarter and a half of your bill. Add roughly $150 to $300 of parts (expansion tank, pan, connectors, gas flex, vent pieces) and the $125 city permit. What's left, roughly $700 to $1,900 on a typical quote, covers labor, disposal, the truck, the warranty, the office, and profit.
That last chunk is where the quotes part ways. Two metro Atlanta plumbing companies publish their own ranges for this exact job. One says $1,200 to $2,500 installed. The other says $2,500 to $5,400. Same tank. Same city. The ranges barely touch.
Neither one is lying. They are different kinds of company. A two-truck licensed plumber has a van and a phone. A big flat-rate brand has billboards, a call center, a fleet, same-day dispatch, and a price book that the technician reads from. You pay for all of it. Some people want that, and it's a legitimate thing to want at 7 p.m. with water on the basement floor.
Two rules of thumb for a standard basement or garage tank in Johns Creek:
- A quote above about $3,500 is paying for the brand, the same-day truck or an extended warranty. Not for extra work on your house.
- A quote under about $1,500 needs three questions answered: is the permit in it, is the expansion tank in it, and is the installer state licensed.
For example, based on our estimate engine, replacing a leaking 13-year-old 50-gallon gas tank in the unfinished basement of a 1996 two-story house in 30022, with a new expansion tank, drain pan, the permit and haul-away, runs about $1,500 to $2,600.
One more thing before your neighbor tells you what they paid in 2022. Tank prices went up. The big manufacturers announced increases of 6 to 9 percent in 2025 and another 3 to 9 percent on various lines in early 2026. Equipment alone is plausibly 10 to 15 percent more than it was two years ago. The neighbor's number is a nice story. It isn't a benchmark.
And those national "average cost" pages showing $1,000 to $1,400? Once the tank alone is $850, that figure does not cover a permitted, code-complete install here. It covers a tank and a handshake.
What Georgia's 2026 code change adds to a swap
Here is the line on the quote that says "code upgrades" and then declines to elaborate.
Georgia made the 2024 plumbing code, with its own amendments, mandatory statewide on January 1, 2026. Three parts of it touch every tank swap. Your 2012 or 2013 install was done under older rules, so the new one can legitimately include things the old one never had.
The expansion tank. If the cold water reaches your heater through a pressure reducing valve, a check valve or a backflow preventer, the code requires a thermal expansion device, and an expansion tank has to sit at least 18 inches of pipe away from the heater's cold inlet. Pressure reducing valves are common in these 1990s subdivisions. Look near your main shutoff for a bell-shaped brass fitting. If it's there, you need the expansion tank. If your old heater had one, it is the same age as the old heater and usually gets replaced with it.
The relief line. The pipe off the temperature and pressure relief valve has to be full size, serve only that valve, run without shutoffs, tees or a threaded end, finish within 6 inches of the floor or a drain, and be somewhere you can see it. Plenty of older installs fail one of those. Fixing it is a few fittings and a short run of pipe.
The sizing table. This one is new to most people and it matters in a city full of four and five bedroom houses. The code now sets a minimum First Hour Rating by bedrooms and baths:
- 3 bedrooms, 2 to 2.5 baths: 60 gallons
- 4 bedrooms, 2 to 2.5 baths: 62 gallons
- 4 bedrooms, 3 to 3.5 baths: 67 gallons
- 5 bedrooms: 70 gallons
First Hour Rating is not tank size. It's how much hot water the heater delivers in a busy hour, and it's printed on the yellow EnergyGuide label. A 50-gallon gas tank typically clears the bar for a three or four bedroom house. A 40-gallon electric tank in a big house is where it can pinch. In a two-heater house the combined rating counts. Ask for the First Hour Rating of the tank being quoted and check it against your bedroom count. Thirty seconds, and you'll know more than most people who've had this done.
On a quote, these items together typically add roughly $150 to $400. That's a fair number. "Code upgrades: $1,200" with no list is not.
One thing the Georgia amendments leave out: earthquake straps. You'll see them in national articles because California exists. A Johns Creek quote that charges for seismic strapping is charging for another state's problem.
The Johns Creek permit is $125
The city requires a permit to replace a water heater. Under the fee schedule, a stand-alone trade permit is $6.50 per $1,000 of job value with a $75 minimum, plus a $50 administration fee on every permit. Any ordinary water heater job lands on the minimum. That's $125.
The city lists the job under both plumbing and mechanical, so ask your installer whether they pull one permit or two on a gas heater. If it's two, figure about $250.
The other numbers worth knowing:
- Work without a permit is charged double the permit fees.
- A failed inspection costs $75 for the first re-inspection and $125 for each one after.
- Change-outs are issued over the counter, and the city describes an online portal for trade permits. The permit will not hold up your hot water.
So "permit included" on a quote means about $125 of city fees plus someone's time to file it and meet the inspector. A quote with the permit missing is not saving you much. It's saving the installer a trip. It also removes the one person in this whole transaction who checks the gas connection and the flue and has nothing to sell you.
A boundary note. ZIP codes 30022 and 30097 spill past the city limits into Alpharetta, Duluth and Suwanee. If your address is outside Johns Creek proper, a different permit office and a different fee apply. Your tax bill will tell you which city you're in.
Attic tanks and two-heater houses
A lot of the larger houses here have two water heaters: one in the basement or garage, one upstairs in the attic or a closet feeding the bedrooms. The upstairs one costs more to replace, roughly $300 to $800 more, and the reasons are not mysterious. A 50-gallon tank weighs about 150 pounds empty. Someone has to carry the old one down and the new one up, usually two someones. The pan and its drain line are not optional over a finished ceiling, and if the existing drain line is missing or goes nowhere useful, that gets fixed too.
If both heaters went in together, they'll die around the same time. Replacing two on one visit runs roughly double the price of one, less a few hundred dollars for the shared trip. Ask for the two-tank price even if you only plan to do one. It's a useful number to have when the second one starts making noises in eight months.
The attic heater is also the usual reason people in Johns Creek start asking about tankless. A tank over the master bedroom is 50 gallons of water waiting for its moment. Which brings us to the next section.
Going tankless: you're paying for the gas line
A gas tankless conversion in Johns Creek runs about $4,000 to $7,000, roughly $2,000 to $4,000 more than a tank. Very little of that gap is the unit.
A standard 50-gallon tank burns about 40,000 BTU. A whole-house tankless burns up to 199,000. That's five times the gas, and the half-inch line that fed your tank for thirty years typically can't deliver it. So the job becomes: a bigger gas line back toward the meter, a new vent through a wall or the roof (the old metal flue is no use to a condensing unit), a condensate drain, and a 120 volt outlet. The price follows the distance. If the meter is on the other side of the basement wall, you're near the low end, and simple conversions do land around $3,000 to $4,000. If the gas has to cross a finished basement, you're not.
Published prices are all over the map here too. One Atlanta company printed "$2,000 to $5,000" for tankless in one article and "starting from $5,000" in another six weeks later. That's not a scandal. That's how much the house matters on this job. Nobody can price a tankless conversion from a zip code, so be wary of anyone who does it over the phone.
Now the good local news. Tankless output depends on how cold the incoming water is, and north Georgia groundwater typically runs in the low 60s. Rinnai's own flow table for a 199,000 BTU unit shows 6.7 gallons a minute with 62 degree inlet water, against 4.7 with 37 degree water. That's roughly 40 percent more hot water than the same box makes in a cold northern state. One unit can typically cover a three-bath house here. A four or five bath house with everyone showering at once may still want two, and that's a real conversation to have with the installer, not a line item to accept.
Ask one more question: whether your gas meter can handle the added load, and what happens if it can't. Have the installer check with Atlanta Gas Light before you sign.
When tankless is the wrong call: the gas run is long, the budget is tight, and the tank it replaces was doing fine. Also think twice about a unit on an exterior wall or in an unheated attic. Tankless units protect themselves from freezing with electricity, and the cold snaps here like to arrive with power cuts.
Electric tanks and heat pump water heaters
Townhomes, condos and some of the 55-plus communities are more likely to have electric heaters. A 40 to 50 gallon electric tank runs about $1,400 to $2,600 installed. It's a simpler job: no gas, no flue. The same sizing table applies though, and a 40-gallon electric tank typically delivers less in the first hour than a 40-gallon gas one. In a four bedroom home, check the label before you assume the same size goes back in.
A heat pump water heater runs about $3,500 to $6,000 before rebates. It uses a fraction of the electricity of a standard electric tank, and Georgia Power pays back half the cost up to $800 on a qualifying model. In an all-electric home with a garage or basement to put it in, that's a straightforward upgrade. It's the wrong choice in a small closet, because it needs air around it to work.
In a gas house, the sums get harder. You'd need a new 240 volt circuit, which costs more. And Georgia's gas market has a quirk: Atlanta Gas Light's base charge reaches you through your marketer no matter how little gas you burn. The state's pricing chart puts it at about $580 a year for a typical customer. Keep a gas furnace or a gas range and you keep paying it. So the heat pump only saves you the therms the old water heater burned, minus the extra electricity. On cost alone, that's a tough case in a house that stays on gas.
Rebates in 2026 are smaller than the internet says
A lot of pages still promise a $600 or $2,000 federal tax credit for a new water heater. That credit ended. Per the IRS, it does not apply to anything placed in service after December 31, 2025. If a salesperson builds it into your math, the math is a year old.
What's left in Johns Creek:
- Standard gas tank: zero. The Atlanta Gas Light rebate pays $200 for a storage tank, but only at an efficiency rating of 0.82 or better. An ordinary atmospheric tank is well below that. The $200 is for condensing and high-efficiency models, which cost a good deal more than $200 extra.
- Gas tankless: $300 from Atlanta Gas Light for a whole-house unit rated 0.87 or better. It has to replace an existing gas heater, be bought from an authorized retailer, and be installed to code by a Georgia-licensed contractor. One per address every ten years, while funds last.
- Rinnai tankless: possibly another $250 from the manufacturer on listed models bought in 2026. It's limited to the first 80 claims, so treat it as a maybe.
- Heat pump water heater: up to $800 from Georgia Power, half the cost, ENERGY STAR model.
- Georgia's home energy rebate: up to $1,750 on a heat pump water heater, for households under 150 percent of area median income. In a city with a median household income around $160,000, plenty of households are over the line, though retirees on a fixed income may well qualify. Check the state's rebate site for the current income table and whether it's taking applications.
Best case on a tankless conversion is $550, call it 5 to 10 percent of the job. Nice. Not a reason to buy one.
The Atlanta Gas Light paperwork has to be in within 45 days of installation, and they mean it. Allow about eight weeks for the check. And since that rebate requires a licensed contractor and a code-compliant install, the handyman special with the permit skipped forfeits it.
Soft water, and the softener you can skip
Somewhere in a national article, you were told hard water destroys water heaters and kills tankless units with scale. True in Phoenix.
Johns Creek water comes from the Chattahoochee and is treated at the Tom Lowe plant, which is in Johns Creek. Fulton County's water quality report put hardness at about 25 milligrams per liter, around 1.5 grains per gallon, and calls it soft. That is very gentle water.
What that means for you:
- A water softener sold alongside the heater "to protect it" is not justified by hardness here. If you want one for other reasons, fine. The heater doesn't need it.
- Tankless manufacturers still call for a periodic flush, and you should follow the manual for the warranty's sake. But scale builds slowly at this hardness, so an annual descaling plan sold with urgency deserves a raised eyebrow.
- Tanks here typically go 8 to 12 years. If yours is 13 and dry, it owes you nothing and you should start collecting quotes while it's still your idea.
What to ask, and what should worry you
Most plumbers around here are decent people working inside a business model that rewards the fast yes. You don't need to catch anyone out. You need the quote to say what's in it.
Ask these:
- Is the Johns Creek permit in the price, and who meets the inspector?
- Which tank, exactly? Brand, model, gallons, warranty years, and the First Hour Rating.
- What code items are included? Expansion tank, pan and drain, relief line, gas shutoff. Listed, with a price.
- What's your Georgia plumbing license number? (You can look it up on the Secretary of State's site in about a minute.)
- Is haul-away included?
- For tankless: what size gas line are you running, from where, and where does the vent go? Has anyone checked the meter?
Red flags:
- No permit, or "you don't really need one for a swap." You do. The city says so, and charges double when it finds out.
- "Code upgrades" as a single large number with no list. The real list is short and runs a few hundred dollars.
- A federal tax credit in the sales pitch. It ended with 2025.
- A softener, a whole-house filter or a descaling contract bundled in "to protect the new heater." See the section on soft water.
- A tankless price quoted before anyone has looked at your gas line. That's a guess with a dollar sign.
If the heater is already leaking, here's how to buy yourself an hour. Turn the gas control knob to off, close the cold water valve above the tank, and run a hose from the drain valve at the bottom to a floor drain or outside. The leak stops being an emergency once the tank is empty. Then get a second number. The real cost of an emergency in this town is rarely an after-hours surcharge. It's saying yes to the first quote because your socks are wet.
Get your estimate
Want a number for your own water heater? Describe the job in the box below, add a photo of the tank and its label if you have one, and you'll get a free estimate in 2-3 minutes. If it looks right, we'll find you a vetted local plumber for the work.
Common questions
How long does a water heater replacement take in Johns Creek?
A tank swap is usually done the same day, often in two to four hours once the plumber arrives. A tankless conversion typically takes a full day, longer if the gas line has to be rerun across the house. The city issues change-out permits over the counter, so the permit doesn't slow anything down.
Can I replace my own water heater in Johns Creek?
Legally, yes. Georgia law lets you do plumbing work in a home you own or live in, and the city will issue the permit to a homeowner who signs an affidavit. It still gets inspected. Expect roughly $1,000 to $1,300 for the tank, parts and the $125 permit. Two cautions: gas connections and flue venting are where carbon monoxide problems come from, and the Atlanta Gas Light rebates require a Georgia-licensed contractor. Hiring an unlicensed installer is a different thing entirely. That's not the homeowner exemption, and it isn't rebate eligible.
Is a 50-gallon tank big enough for a four or five bedroom house?
Often, but check. Georgia's 2026 code sets a minimum First Hour Rating: 62 gallons for four bedrooms with up to 2.5 baths, 67 with 3 to 3.5 baths, 70 for five bedrooms. The rating is on the yellow EnergyGuide label and is usually well above the tank's gallon size on a gas model. If your house has two heaters, their ratings are added together.
Should I replace both water heaters at the same time?
If they're the same age and one has failed, the other is close behind. Doing both on one visit typically costs roughly double a single tank, less a few hundred dollars for the shared trip and setup. If the second one sits in the attic over finished ceilings, the case for doing it now is stronger, since a leak up there costs far more than the heater.
My neighbor paid $1,400 a couple of years ago. Why is my quote higher?
Three reasons. Manufacturers raised tank prices in 2025 and again in early 2026, so equipment alone is plausibly 10 to 15 percent higher. Georgia's code changed on January 1, 2026, which can add an expansion tank and relief line work the neighbor's job didn't include. And the neighbor's price may have skipped the $125 permit. Compare line by line, not total to total.
Get the number for your own job
A typical job is a starting point, not your job. Describe yours (a photo helps) and the same estimate engine prices it for Johns Creek in 2-3 minutes. Free, and nobody gets your number.
Sources (22)
- https://johnscreekga.gov/app/uploads/2024/07/community-development-fee-schedule.pdf
- https://johnscreekga.gov/departments/community-development/building-permitting/do-i-need-a-permit
- https://johnscreekga.gov/quicklinks/faqs/building-faqs
- https://johnscreekga.gov/departments/community-development/building-permitting/guide-for-online-permit-portal
- https://dca.georgia.gov/document/document/ipc-2026-amendment-packet/download
- https://dca.georgia.gov/document/document/new-codes-and-amendments-effective-january-1-2026-memo/download
- https://www.irs.gov/newsroom/faqs-for-modification-of-sections-25c-25d-25e-30c-30d-45l-45w-and-179d-under-public-law-119-21-139-stat-72-july-4-2025-commonly-known-as-the-one-big-beautiful-bill-act-obbb
- https://www.atlantagaslight.com/residential/ways-to-save/rebates/efficiency-rebate.html
- https://www.atlantagaslight.com/content/dam/southern-co-gas/agl/docs/rebates/manufacturer-rebates/manufacturer-rebates-2026/rinnai-2026-southern-company-gas-consumer-rebate.pdf
- https://www.georgiapower.com/content/dam/georgia-power/pdfs/programs/heip/HEIP_Preconditions_Requirements_2026.pdf
- https://energyrebates.georgia.gov/her-faqs
- https://fultoncountyga.gov/-/media/Departments/Public-Works/Water-Quality-Reports/2025-CCR-final-FOR-WEB.pdf
- https://fultoncountyga.gov/-/media/Departments/Public-Works/Water-Quality-Reports/CCR2016.pdf
- https://psc.ga.gov/site/assets/files/9686/august_2026_variable_pricing-1.pdf
- https://law.justia.com/codes/georgia/2019/title-43/chapter-14/section-43-14-13/
- https://media.rinnai.us/salsify_asset/s-d45cc867-0f5a-4039-9885-98e042f012df/US and Canada Ground Water Maps.RX and RXP199IN.pdf
- https://homedepot.com/b/Plumbing-Water-Heaters/50-gal/N-5yc1vZbqlyZ12laZ12lcZ1z1t3pn
- https://biztimes.com/a-o-smith-raises-water-heater-prices-between-6-and-9-to-mitigate-tariffs/
- https://www.supplyht.com/articles/107084-phcp-pvf-price-increases-february-march-2026
- https://www.rooterplus.com/blog/water-heater-replacement-cost-in-atlanta-2026-price-guide
- https://www.estesair.com/blog/water-heater-installation-cost-in-georgia
- https://www.estesair.com/blog/cost-of-tankless-water-heater-in-2026
Researched for Johns Creek, GA · Updated November 15, 2026 · Reviewed by Ralph Cockburn on November 16, 2026 · How these guides are made
Prices are researched local ranges, not quotes. The contractor who sees your job sets your actual price. More Johns Creek cost guides