HVAC Replacement Cost in Edmond, OK (2026 Prices)

The short answer

Odds are your furnace and AC went in together, around the same time as the house or the last big remodel, and they've now been at it for about twenty Oklahoma summers. That's the usual Edmond story. Nearly half the homes here were built after 2000 and almost all the rest between 1970 and 1999, so a lot of original systems are hitting the age where the repair quotes start sounding like a down payment.

For one standard-efficiency system (a new gas furnace, AC condenser and matching coil, 3 to 4 tons, reusing your ducts), expect roughly $8,500 to $12,500 installed in Edmond in 2026. A higher-efficiency system (two-stage or variable-speed AC with a 95%+ two-stage furnace) runs about $13,000 to $18,500.

The other common versions:

  • AC only (new condenser and coil, keep the furnace): about $6,000 to $9,000
  • Furnace only: about $4,500 to $8,000
  • Heat pump with air handler (all-electric): about $9,000 to $15,000
  • Dual fuel (heat pump plus gas furnace backup): about $11,000 to $19,000

Two systems, one per floor? Plan on close to double.

Same numbers whether your AC quit in July, a buyer's inspector flagged a 20-year-old furnace, or hail turned the condenser fins into modern art. The reasons a quote lands high or low don't change, and neither do the rebates, which in Edmond are unusually tangled. More on that below, because one of them disappears if you don't book an energy audit before the install.

Why the internet says $1,400

If you searched first, you probably saw a furnace "replacement" for around $1,400 and heat pumps for $3,100 to $8,300. Those pages are national templates with "Edmond" typed into the city field. Lovely numbers. Nobody in central Oklahoma can install equipment for them.

The cheapest advertised flat-rate swap in the OKC metro is about $6,500, and that's a 2.5 to 3.5 ton Goodman AC with an 80% furnace, before any change to ducts, wiring, gas lines or the refrigerant lines. One local contractor publishes its tiers: about $8,755 for an entry-level 14 SEER2 system, $9,860 for a RunTru by Trane system, $12,610 for a Trane XR14 setup, then roughly $14,780 and $18,167 for its two higher-efficiency tiers. OKC-area homeowners report the same thing from the other side of the kitchen table: about $9,000 for a 4-ton Trane on a 1,900 sq ft house, around $11,000 from another company, $13,000 for an upgraded two-stage system.

So if your quote says $10,500 and you saw $1,400 online, the quote isn't the weird one.

What moves the price on your system

Contractors here quote all-in, not labor plus parts, so you'll rarely see an hourly rate. The price moves with these things instead.

Efficiency tier and brand. This is the biggest lever, and it's mostly a choice, not a surprise. Going from a basic single-stage system to a two-stage or variable-speed one adds roughly $3,000 to $6,000. A 95% furnace over an 80% one is about $1,500 to $2,000 more in national pricing, before the gas-company rebate knocks some of that back.

Where the furnace lives. In a lot of Edmond ranches it's in a hall closet or the garage. In many newer and two-story homes it's lying sideways in the attic. Attic installs take more labor (hauling a furnace up a pull-down ladder in August is nobody's idea of fun), and current code, which Edmond adopted with its 2018 code update, calls for a clear path to the unit, a work platform, a light and an outlet near it. If your attic setup predates that, the fix shows up on the quote. It's typically a few hundred dollars, sometimes more if the path needs decking. A good installer also adds a secondary drain pan with a float switch so a clogged drain doesn't come through your ceiling.

Ductwork. Every price above assumes your existing ducts get reused. Local contractors bill duct changes separately. Crushed attic flex duct in a 1990s house, or ducts that are too small for a new variable-speed unit, can add a meaningful chunk. Ask whether they measured static pressure or just eyeballed it.

Size and number of systems. A 4-ton system costs more than a 2.5-ton one, though less than you'd think, since most of the labor is the same. A second system for the upstairs is the real jump: roughly 1.8 to 2 times the single-system price. Some owners stagger them a year or two apart. That's reasonable if the younger one is healthy.

Electrical, gas and refrigerant lines. A new disconnect or breaker, a gas line moved a few feet, or new copper lines for the refrigerant each add to the bill. The flat-rate deals tend to exclude all of them.

Which company you call. One OKC homeowner reported a $4,000 gap between the cheapest and most expensive quote for the same equipment. That's normal in this trade, and it's why one quote is never enough.

For example, a single-story late-1990s brick house in Edmond of about 2,100 sq ft, swapping a 20-year-old 4-ton AC, coil and attic furnace for a standard-efficiency system on the existing ducts, comes out at about $8,000 to $14,500 in our estimate engine.

Your equipment options in Edmond

Oklahoma sits in the Department of Energy's Southeast region, so a new split AC under about 3.75 tons has to be at least 14.3 SEER2 (13.8 SEER2 for bigger units), a notch above the floor in the northern states. In practice, every entry-level system sold here already meets it. It mainly means a national calculator that assumes the northern minimum runs a bit low.

Gas furnace and AC, 80% furnace

About $8,500 to $12,500 for the whole system. This is the standard Edmond replacement and the right call for most houses with gas. The 80% furnace vents up the existing metal flue, so there's no venting rework. Furnaces commonly last 15 to 20 years or more, and condensers about 12 to 17 years in Oklahoma heat and hail.

When it's wrong: when you want the Oklahoma Natural Gas furnace rebate, which only pays on 95%+ furnaces. Also if your house has no gas service, as on some acreage that runs on propane.

Gas furnace and AC, 95%+ furnace

About $1,500 to $2,000 more than the 80% version, offset by an ONG rebate of roughly $550 to $650. It burns less gas, which matters in a cold February.

A 95% furnace vents through PVC pipe and makes condensate water that has to drain somewhere. In an attic, that means drain routing and a pan. And if the old furnace shared a flue with your gas water heater, the water heater may need its own liner or a resized vent once the furnace stops sharing it. Ask about that before you sign.

When it's wrong: when the vent route is long or awkward and the extra labor eats the rebate and then some.

Heat pump with air handler (all-electric)

About $9,000 to $15,000. One machine cools in summer and heats most of the winter, with electric heat strips for the coldest nights. Edmond Electric pays well for these (see the rebate section). You need a properly sized breaker and circuit for the heat strips, and an older panel may not have room.

When it's wrong: when you have gas, like the heavy warmth of a furnace in an ice storm, and don't want to lean on heat strips when it drops into the teens. Also when the panel needs an upgrade to carry it.

Dual fuel (heat pump plus gas furnace)

About $11,000 to $19,000, or roughly $2,000 to $5,000 more than a furnace and AC. The heat pump handles cooling and mild-weather heating, and the furnace takes over when it gets cold. Local contractors typically set the switch around 35°F and say the heat pump carries about 85% of the heating season. Edmond Electric requires the outdoor lockout set at 40°F or lower for its rebate.

This is the setup that can collect from both sides: $500 to $1,000 from Edmond Electric on a 4-ton system, and possibly ONG's furnace rebate if the furnace is 95%+ (confirm that with ONG first).

When it's wrong: on a tight budget. It's the most expensive ducted option short of geothermal.

Ductless mini split

For the bonus room over the garage that's never been comfortable, a shop, or an addition. Pricing runs per indoor head and varies a lot, so get it quoted. Edmond Electric pays $150 per ton on units of 18 SEER or better, and the city permit is $60. As a whole-house replacement in a ducted Edmond home, it's usually the wrong tool.

Geothermal

About $18,000 to $35,000. Oklahoma is geothermal's home turf, and Edmond Electric pays $800 per ton for a new all-electric geothermal system ($250 per ton for a replacement or dual-fuel one), with a required water-heating add-on. Worth a look on acreage where you'll stay a long time. Overkill for most tract lots.

Two utilities, paying you in opposite directions

This is the Edmond-specific part, and the one the national pages miss entirely.

Most of Edmond buys electricity from Edmond Electric, the city-owned utility, not OG&E. Most homes buy gas from Oklahoma Natural Gas. Each one runs a rebate program, and they pull in opposite directions.

Edmond Electric pays you to go heat pump. Its heat pump rebate pays per ton on replacement systems:

  • Heat pump: $175 to $300 per ton (17 SEER up to 21+ SEER)
  • Dual fuel: $125 to $250 per ton
  • Mini split: $150 per ton

On a typical 4-ton system that's about $700 for a 17 SEER heat pump and $1,200 at 21+ SEER, or $500 to $1,000 for dual fuel. Every tier also has minimum EER and HSPF ratings, so check the exact model against the city's page.

Oklahoma Natural Gas pays you to go gas. Its heating system rebates pay about $550 to $650 for a 95%+ furnace, and about $2,000 to $2,900 for replacing a heat pump with a gas furnace and AC (the higher amounts go with a 95% furnace). ONG's own web page and its 2026 form show different amounts, funding is first come, first served, and you need an Oklahoma-licensed contractor plus the equipment's AHRI certificate. Check the current form before you count on a number.

So if you have a heat pump now and you're thinking of going back to gas, ONG may pay you a couple thousand to do it. If you have gas and want a heat pump or dual fuel, Edmond Electric pays. Neither is wrong. They just want different things from you.

The audit trap

Here's the one that bites people. Edmond Electric requires an in-person energy audit by a certified auditor before any changes are made. Not after. If the new heat pump is already humming when you find out, that rebate is gone. The rest of its rules:

  • the permit has to be closed, with a copy or photo of the final inspection tag
  • the contractor agreement goes on file
  • you file within 90 days of install
  • no rebate if the same address got one in the last 10 years

If you're anywhere near a heat pump or dual fuel decision, call Edmond Electric about the audit the same day you call contractors.

Check which electric company is on your bill

Edmond covers about 90 square miles, and the city's own service area map draws the city limits and the Edmond Electric territory as separate lines. Some outlying addresses are served by OG&E or a rural co-op, with different rebates. Look at your electric bill before you plan around any of the numbers above.

The federal tax credit is gone

If you've read that a heat pump gets you $2,000 back from the IRS, that was true through 2025. Under the One Big Beautiful Bill Act, the IRS says the energy-efficiency credit is not allowed for anything placed in service after December 31, 2025. The old $600 for a furnace or AC is gone too.

For a 2026 install in Edmond, the only money back is the utility rebates above. Any quote or article that still subtracts a federal credit is doing math from last year.

The refrigerant change and the $4,000 condenser quote

Since 2025, new AC and heat pump systems use a new class of refrigerant (R-454B in Trane and RunTru, R-32 in Goodman and Amana). Manufacturers priced the new equipment higher, roughly high single digits to 10% or more at launch, and the refrigerant itself got pricier too.

The practical upshot: a new condenser needs a matching new coil. You can't bolt a new-refrigerant outdoor unit onto your old indoor coil. That's why one OKC homeowner's quotes looked like this for the same 20-year-old system: about $4,000 for a condenser only, $7,000 for condenser and coil.

That $4,000 option is still legal. In May 2026 the EPA dropped the 2026 install cutoff, so R-410A units built or imported before 2025 can still be installed until the stock runs out. It's a real way to save money now. The trade is that R-410A for future repairs will keep getting scarcer and more expensive as production winds down. If your furnace and coil are young and you plan to move in a few years, it can make sense. If everything is 20 years old, you're patching a system that's about to need the rest anyway.

The permit costs about $70. Skipping it costs more.

Swapping a furnace and AC in Edmond needs a mechanical permit from the city's Building & Safety department. Per the city's fee schedule, it's $35 per furnace and $35 per AC, so about $70 for a typical changeout (more if ductwork is added or altered, which is its own permit line). Starting work without a permit triples the fee.

Seventy dollars is not where anyone saves money. And because Edmond Electric wants the final inspection tag, a contractor who offers to skip the permit is offering to save you $70 and cost you a $700 to $1,200 rebate. The inspection also checks the gas connection, venting and condensate drain, the parts of this job you really want a second set of eyes on. Buyers' inspectors in Edmond ask about unpermitted work too.

Oklahoma also requires HVAC contractors to hold a state mechanical license, and both utility rebates require a licensed installer. Ask for the license number. It takes a minute to check.

What to ask, and red flags in a quote

Good HVAC contractors here will answer all of these without flinching. Ask:

  1. What exactly is included? Furnace, condenser, coil, refrigerant lines, pad, disconnect, thermostat, permit, haul-away. Get model numbers, not just "Trane 3-ton".
  2. How did you size it? A proper load calculation (Manual J) beats "you had 4 tons, you get 4 tons". Many older installs are oversized, and an oversized AC in a humid Oklahoma summer cools fast and leaves the house clammy.
  3. Will you pull the permit, and is the final inspection included?
  4. Does this equipment qualify for the Edmond Electric or ONG rebate, and will you do the paperwork? For Edmond Electric, ask whether the audit is booked before install day.
  5. Is this a new-refrigerant system or leftover R-410A? Either can be fine. You should know which one you're buying.
  6. If it's a 95% furnace, what happens with the water heater vent?
  7. What's the cash price? Promotional financing is often built into the quoted price. Ask both ways.

Red flags:

  • "We'll skip the permit and save you some money." See above. It's the most expensive $70 you'll ever save.
  • A federal tax credit subtracted from the price. It ended with 2025.
  • A quote far under $6,500 for a full system. Something's missing, usually the coil, the lines, or the permit.
  • No model numbers, or a line like "high-efficiency system" with no SEER2 rating attached.
  • Pressure to sign today because a price "expires tonight." The equipment will still be there tomorrow. So will a good contractor.
  • One quote. With a $4,000 spread on identical equipment, get at least two.

Get your estimate

Want a number for your own system? Describe the job in the box below, add a photo of the unit labels if you have one, and you'll get a free estimate in 2-3 minutes. If it looks right, we'll find you a vetted local HVAC contractor for the work.

Common questions

How much does it cost to replace HVAC in a two-story Edmond house with two systems?

Plan on roughly 1.8 to 2 times the single-system price, so about $15,000 to $25,000 for two standard-efficiency furnace and AC systems. Some contractors trim the second one a little since the crew is already there. If one system is much younger, replacing them a year or two apart is a reasonable way to spread the cost.

Is a heat pump a good idea in Edmond winters?

It can be, especially as dual fuel: the heat pump covers mild days and the gas furnace takes over in hard cold. All-electric heat pumps work here too but lean on electric heat strips during cold snaps, so check that your panel can carry them. Remember the Edmond Electric rebate requires an energy audit before install.

Should I replace just the AC and keep my furnace?

If the furnace is under about 10 to 12 years old and healthy, often yes. Expect about $6,000 to $9,000 for a new condenser and matching coil. If both are around 20 years old, replacing them together usually costs less than two separate visits.

How long does an HVAC replacement take?

Most replacements are done in one day, typically 4 to 8 hours. Attic furnaces or ductwork changes can stretch it to two days. Booking can take longer during a July heat wave or a February freeze, when every company in the metro is busy, so if your system is limping, getting quotes before it dies gives you time to compare.

What permit do I need to replace a furnace or AC in Edmond?

A mechanical permit from the City of Edmond, about $35 per appliance, so around $70 for a furnace and AC. Your contractor normally pulls it. Keep the final inspection tag, since Edmond Electric asks for it with rebate paperwork.

Get the number for your own job

A typical job is a starting point, not your job. Describe yours (a photo helps) and the same estimate engine prices it for Edmond in 2-3 minutes. Free, and nobody gets your number.

Sources (19)

Researched for Edmond, OK · Updated November 11, 2026 · Reviewed by Ralph Cockburn on November 16, 2026 · How these guides are made

Prices are researched local ranges, not quotes. The contractor who sees your job sets your actual price. More Edmond cost guides