HVAC Replacement Cost in Allen, TX (2026 Prices)

The short answer

The outdoor unit made a noise it had never made before. Then it made no noise at all. Now somebody has handed you a number with a comma in it, and you'd like to know if it's a fair one.

Here's the honest version. In Allen, replacing one full standard-efficiency system (outdoor AC unit, indoor coil and the gas furnace in the attic) typically runs $9,500 to $14,500 in 2026. That's for the usual 3.5 to 4 ton system serving the downstairs of a 1995-2010 brick two-story, reusing the existing ducts.

The other common versions of the job, installed, one system unless noted:

  • New outdoor unit and coil, keeping the furnace: about $6,500 to $10,000
  • Heat pump plus coil, keeping the gas furnace as backup (dual fuel): about $8,000 to $12,500
  • High-efficiency two-stage or variable-speed full system: about $14,000 to $20,000 and up
  • Both systems in a two-system house: about $17,000 to $27,000
  • Furnace only: about $3,500 to $6,500
  • One-room ductless mini split: about $3,500 to $7,000

Those ranges are built from Dallas-area pricing and adjusted for this year's manufacturer increases, so treat them as a solid read, not a price list. A dead compressor in July isn't the only way people end up here, either. Hail took out the condenser, the system is 20 years old and you'd rather choose the day than have August choose it for you, or an inspection report on a house you're buying or selling just flagged it. The numbers and the logic below work the same for all of those.

Why "just the outdoor unit" mostly stopped being an option

This is the part that confuses people with an old quote in a drawer, so it goes first.

New split systems now use a different class of refrigerant (R-454B or R-32, called A2L refrigerants). A new A2L outdoor unit has to be paired with a matching new indoor coil. Your old coil was built for R-410A and there's no field conversion. A fire marshal's code interpretation under the same 2021 mechanical code family that Allen has adopted spells it out: the existing indoor coil "is required to be replaced." So the old cheap move, swap the condenser and walk away, now means condenser plus coil, about $6,500 to $10,000.

There's one leftover exception. EPA dropped the 2026 install deadline for R-410A condensers built before 2025, so a contractor who still has one on the shelf can install it with your old coil for roughly $4,000 to $6,500. Nobody is making new ones, and the stock is shrinking. If a contractor offers this, it's legitimate. It also means you're buying a brand-new unit that runs on a refrigerant that's being phased down, so repair refrigerant later won't get cheaper.

The good news: your furnace can usually stay. The A2L rules don't require a new furnace if the furnace manufacturer and the new coil's instructions allow it. That often means wiring a refrigerant leak sensor to the furnace blower and confirming airflow, which is normal work, not a scam. So when a quote includes a new furnace, ask whether it's required or recommended. A sound furnace that stays is worth roughly $3,500 to $5,000 on a single system. Furnaces here run few hours and often last 20+ years, so a 15-year-old furnace with a clean heat exchanger isn't automatically done. A 20-year-old one, matched to an AC that just died, is a reasonable thing to replace at the same time. That's a judgment call, and a good contractor will tell you which one you're looking at and why.

The two-system house problem

A lot of Allen homes were built between 2000 and 2010, and the typical 2,200 to 3,500 sq ft two-story has two separate systems: a 3.5 to 4 ton downstairs and a 2 to 3 ton upstairs. The builder installed them the same week. They've aged together. When one dies, the other one is usually just behind it.

So the real question isn't only "what does this cost" but "do I do one or both." One full system is about $9,500 to $14,500. Both together are about $17,000 to $27,000, with some savings from one trip, one setup and one permit visit. That's $7,000 to $12,000 spent on a system that might have a few good years left.

A reasonable middle path: replace the one that failed, and ask for the second system to be quoted at the same time, in writing, with how long that price holds. You get a real number to plan around without front-loading the whole bill. If the surviving system is already struggling (short cycling, refrigerant top-offs, a hot upstairs that never quite catches up), doing both now starts making more sense.

What moves the price on one system

Size. Price climbs with tonnage, but less than you'd think. A 4-ton full system costs more than a 3.5-ton, maybe by $1,000 or so. The bigger risk is the wrong size. Many 2000s houses were sized generously when they were built. A proper load calculation (Manual J) is how a contractor finds out whether you need what you had. Ask if they did one, or at least how they decided.

Efficiency. Texas sits in DOE's Southeast region, where the federal minimum for split AC is 14.3 SEER2 under about 4 tons and 13.8 SEER2 at 4 tons and up. The old 13 and 14 SEER units can't be installed anymore. Stepping up to two-stage or variable-speed adds roughly $3,000 to $6,000 per system.

The attic. Allen furnaces and coils mostly live in the attic, with flex duct running off them. Attic work is hotter, slower and fussier than a closet install. Expect quotes to include a secondary drain pan with a float switch, condensate routing, and sometimes a platform or better access. On a straightforward change-out those items add about $500 to $1,500, often bundled.

Ducts. If the 20-to-25-year-old flex duct is crushed, disconnected or sagging, sealing runs $300 to $800, and full replacement $3,000 to $8,000. A new system on bad ducts is a very nice engine in a car with flat tires. Ask the contractor to look while they're up there and show you photos.

Line set and electrical. Reusing the copper line set is often allowed if it meets the new manufacturer's requirements. A new one is around $700, more on a two-story with a long run. Breaker, disconnect or wiring changes add $400 to $650 or more. A new condenser pad is $100 to $300.

Labor. Local HVAC wages are about average for the country, so Allen isn't expensive because of the crews. A like-for-like change-out is usually one day for a two- or three-person crew, with labor typically $2,000 to $4,000 of the total per system (more for a tight attic).

The permit. Allen's fee schedule lists $175 for a complete HVAC system on a house, issued by the City of Allen, not the county. Contractors also register with the city each year. It's about 1-2% of the job. It's not the place to save money.

Which equipment makes sense here

Standard single-stage AC (14.3 to 15.2 SEER2). The cheapest legal new system and the one in most of the ranges above. Around here it typically lasts 12 to 17 years, because DFW summers are long and compressors earn their money. It's the wrong choice if you have a hot upstairs that never evens out, where a two-stage unit runs longer at low speed and pulls more humidity. It's also wrong if you're planning around Oncor's incentive, since many base units don't meet its efficiency bar (more on that below).

Two-stage or variable-speed (16 to 22 SEER2). About $3,000 to $6,000 more per system. Quieter, more even, better at humidity. Lifespan is similar, and the inverter boards are one more expensive part that can fail. It's the wrong choice if you're keeping an older furnace that can't run a matched variable-speed blower (you'll pay for capability you can't use), or if you expect to sell within about five years.

Heat pump with your gas furnace as backup (dual fuel). Often $0 to $2,000 more than the AC equivalent. The heat pump handles cooling and most of the heating, and the gas furnace takes over on the cold nights. That suits a lot of Allen homeowners who remember February 2021 and don't love the idea of going all-electric. Expect 12 to 15 years, since it runs year-round. It needs a thermostat that can manage dual fuel. It's the wrong choice if your furnace is near the end and you'd rather do one clean swap, or if your electrical panel is tight and someone is proposing an all-electric air handler with heat strips instead.

80% gas furnace (horizontal, attic). $3,500 to $6,500 on its own, usually bundled into a full change-out. These last a long time here. Replacing a sound one just so everything "matches" when only the AC failed is the most common $3,500 you don't have to spend. Ask the contractor to check the manufacturer's match for the new coil with your existing furnace first.

Ductless mini split (single zone). $3,500 to $7,000 for one room. Good for the bonus room over the garage, a garage conversion or a sunroom. Wall heads and visible line sets on a street-facing wall may need HOA sign-off, so ask before you pick a spot. It's the wrong fix for a whole floor that's uncomfortable because of leaky or undersized ducts. Fix the ducts.

For a sense of a real job: based on our estimate engine, replacing the whole downstairs system (a 20-year-old 4-ton AC with its coil and 80% attic furnace) in a 2,700 sq ft 2004 two-story in 75002, with a standard-efficiency matched system and the existing ducts kept, comes out to about $8,000 to $13,500.

The money that isn't coming this year

A lot of pages online still subtract rebates and credits that don't apply to a 2026 install. Budget the full installed price.

The federal tax credit is gone. The 25C credit (it used to be up to $2,000 for a heat pump, $600 for an AC or furnace) doesn't apply to equipment placed in service after December 31, 2025. If a quote nets it out, the quote is wrong.

Texas's federal-funded home energy rebates aren't live. The Comptroller's page says plainly that rebates are not currently available. They may open in 2027, likely with income limits.

Oncor's 2026 incentive money is spent. Allen sits in Oncor's territory, and its program does cover high-efficiency central AC, heat pumps and mini splits, not only heat pumps. The per-system caps run from $2,000 for a 2-ton up to $3,400 for a 5-ton ($3,200 for a 4-ton), but those are ceilings. The actual payout is calculated from the energy saved, so a modest upgrade gets a modest check. The equipment needs at least 11.6 EER, the contractor has to be a participating one, and the job has to be permitted. And as of now, Oncor's own page says 2026 funding is fully exhausted, and it says to check back in January 2027 (these programs usually run from about February into November).

If your system still runs and you were leaning toward a higher-efficiency unit anyway, waiting for the 2027 round can make sense. If it's dead and it's your house, don't hold out for an incentive with an unknown amount.

Is November a good time to replace?

Mostly, yes. DFW's 100-degree days typically start around July 1 and end around August 27, and that's when systems fail and schedules fill. In October through April, crews have room, you can get several quotes without sweating through the wait, and nobody is pricing in a heat emergency.

The catch is equipment pricing. Carrier announced an 8% residential equipment increase landing toward the end of 2026, and Trane raised prices up to 5% twice this year. Equipment is roughly a quarter to two-fifths of an installed price, so that works out to very roughly $200 to $500 more per system if it's fully passed through. Real, but smaller than the gap you'll often see between two quotes for the same job. Also: a quote from 2024 or early 2025 isn't a useful comparison. That was before the refrigerant switch and two rounds of increases.

Hail-damaged condensers and your deductible

Collin County gets hail, and condensers sit outside taking it. Here's the uncomfortable math: in North Texas, 2% wind and hail deductibles are now standard, and some policies are 3%. On a house insured for about $450,000, 2% is $9,000. A hail-dented condenser, at roughly $4,000 to $10,000 to replace, usually doesn't clear that on its own.

Where it matters is when you're already filing a roof claim from the same storm. Make sure the condenser (and any bent fins or damaged line set) is on that claim with photos. Bent fins alone can often be combed straight. A dented coil that won't cool is a replacement.

How to read an Allen HVAC quote

The tax line isn't a trick. In Texas, labor on residential repair and remodeling isn't taxed. On a lump-sum quote the contractor pays tax on the equipment and builds it in. On a quote that separates materials from labor, you'll see sales tax on the materials only, roughly $400 to $600 at Allen's typical rate. Compare totals, not whether one quote "has tax."

What to ask every contractor:

  • What exactly is being replaced: condenser, coil, furnace? If the furnace is included, is that required by the manufacturer match, or a recommendation, and why?
  • What's the model number of each piece, and can I see the AHRI match certificate? (That's the document showing the outdoor unit and coil are rated together.)
  • How did you size it? Did you run a load calculation or just match the old tonnage?
  • Are you reusing the line set? If not, why?
  • What attic items are included: drain pan, float switch, leak sensor, platform, condensate routing?
  • Did you look at the ducts? What did you see?
  • Will you pull the City of Allen permit and schedule the inspection?
  • If the second system is the same age, what would it cost to do it now, and how long does that number hold?

Red flags:

  • No permit, or "you don't need one for a swap." Allen charges $175 for exactly this. An unpermitted replacement can come up at resale, and it shuts you out of Oncor's program in years when there's money.
  • A new A2L outdoor unit hooked to your old coil. That's the shortcut the code interpretation above rules out.
  • A quote that subtracts a federal tax credit for a 2026 install.
  • A total with no model numbers, just "4-ton system, $X."
  • Pressure to sign today because "prices are going up." They are, by a few hundred dollars. That's not worth skipping a second quote over.
  • A new furnace presented as mandatory with no explanation, when yours is sound and the manufacturer match allows it to stay.

None of this makes the contractor a villain. Most quotes in Allen are written by people who've been in a lot of hot attics and are trying to give you a system that won't bring them back on a callback. Asking these questions just gets you their reasoning on paper, which is where you want it.

Get your estimate

Want a number for your own system? Describe the job in the box below, add a photo of the outdoor unit's label if you have one, and you'll get a free estimate in 2-3 minutes. If it looks right, we'll find you a vetted local HVAC contractor for the work.

Common questions

Should I repair my 20-year-old AC or replace it?

If the compressor has failed or the coil is leaking, replacement usually wins. A repair on a 20-year-old R-410A system often costs a meaningful slice of a new system, and parts and refrigerant for it won't get cheaper. For a capacitor, contactor or fan motor, repair is usually fine even on an old unit. Ask for both prices and the age of the parts being replaced.

Can I just replace the outdoor unit and keep everything else?

Only if the contractor still has a pre-2025 R-410A condenser in stock, which is getting rarer, at roughly $4,000 to $6,500. A new A2L outdoor unit needs a matched new indoor coil, so the usual "AC only" job is now about $6,500 to $10,000. Your furnace can usually stay.

Are there any rebates for a new AC or heat pump in Allen right now?

Not for a late-2026 install. The federal 25C credit ended for equipment installed after 2025, Texas's federal-funded rebates aren't open, and Oncor's 2026 program money is used up. Oncor says to check back in January 2027, and the program requires higher-efficiency equipment and a participating contractor.

Do I need to replace both systems in a two-story at the same time?

No. Replace the one that failed and get the second system quoted at the same time so you have a real number for later. Doing both at once saves some money on the second one, but if it's still running well you're not required to spend $7,000 to $12,000 early.

How long does an HVAC replacement take?

A like-for-like change-out of one system is usually a one-day job. Two systems, or added duct, line set or electrical work, can take one to two days. The City of Allen inspection typically happens after the install.

Get the number for your own job

A typical job is a starting point, not your job. Describe yours (a photo helps) and the same estimate engine prices it for Allen in 2-3 minutes. Free, and nobody gets your number.

Sources (24)

Researched for Allen, TX · Updated November 11, 2026 · Reviewed by Ralph Cockburn on November 16, 2026 · How these guides are made

Prices are researched local ranges, not quotes. The contractor who sees your job sets your actual price. More Allen cost guides